Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
Display Glass cleaning products: Clean using a soft cloth. Do not use alcohol, vinegar or other abrasive or acidic cleaning products. Glass panel Glass cleaning products: Clean using a soft cloth. Do not use a glass scraper. Door covering Only use products specially for cleaning stainless steel (these can be obtained from the Technical Assistance Service or from specialist shops) . Follow the manufacturer's instructions. Zone Cleaning products Oven interior Hot water with a little soap or water and vinegar: Clean with a dishcloth. If very dirty, use a stainless steel scourer or special oven cleaning products. These must only be used on a cold oven. Whenever possible, use the self- cleaning function. See the chapter on the Self-cleaning function. Oven carriage base Hot water with a little soap or water and vinegar: Clean with a dishcloth. Glass cover for the oven Hot water and a little soap: light Clean with a dishcloth. Seal ( do not remove) Hot water and a little soap: Clean with a dishcloth. Do not rub. Accessories Hot water and a little soap: Soak them clean using a dishcloth or brush. Light The oven light can be turned on manually to facilitate cleaning. Connecting the oven bulb Turn the function control knob to the N position. The light will come on. Turning the oven light off Turn the function control knob to the Uposition. Removing the oven carriage The oven carriage can be easily removed to make cleaning the oven easier. Pull out the oven carriage its full limit. Hold the carriage on both sides, lift it slightly and remove it. Place it carefully on a flat surface. The base of the oven contains delicate components. After cleaning, the oven door can be refitted by repeating the procedure in reverse. Removing the door covering The oven carriage cover can change colour with time. For better cleaning, we recommend removing the cover. 1. Open the oven carriage 2. Unscrew the oven carriage door cover. To do this, unscrew the right and left hand side bolts (figure A). Hold the outside door glass with one hand. The glass tilts slightly inwards. 3. Remove the cover ( figure B) . Ensure that the oven carriage does not close when the cover is not in place. The outside glass may damage. Clean the surface using a product specifically for cleaning stainless steel. 4. Refit and secure it. 5. Close the oven carriage Fitting and removing the glass panels To make cleaning easier, the glass from the oven carriage can be removed. Removing 1. Removing the oven carriage 2. Remove the top cover of the oven carriage. To do this, unscrew the right and left hand side bolts ( figure A) . 3. Hold the glass in your hands (left and right) and remove upwards (figure B). Place these with the handle downwards on a cloth. The inside glass with the hooks should not be removed from the oven carriage. 4. Unscrew the clips from the right and left and remove them (figure C) . Remove the top glass panel. Clean the glass panels using a glass cleaning product and a soft cloth. Do not use abrasive or corrosive cleaning products, glass scrapers, or hard metal scourers as these could damage the glass. Installing When installing the glass, check that the phrase " right above" on the bottom left- hand side is upside down. 1. Insert the glass panel by tilting it ( figure A) . 2. Position and screw the clips to the right and left ( figure B) . 3. Insert the glass into the carriage support. 4. Fit and tighten the screws on the cover. If the cover cannot be screwed into place, check that the glass has been correctly fitted on the support. 5. Close the oven carriage. Once the glass panels have been correctly fitted, the oven is ready to use. Troubleshooting Quite often, when there is a malfunction, it is usually a small irregularity which is easy to rectify. Before contacting the Technical Assistance Service, try to determine the cause of the fault using the following table. Troubleshooting table Fault Possible cause Solution/ advice The oven does The fuse has Check the condition of the not work. blown. fuse/circuit breaker in the fuse box. Power cut Check that the light in the kitchen and other household appliances are working. The 0 symbol Power cut Set the time once again. lights in the display with some zeros. The oven does There is dust in Turn the control knob not work. the contacts. several times in both directions. The oven door The oven door Wait until the oven has does not open. has been cooled and the H symbol The Hsymbol locked by the turns off. lights up on the self-cleaning display panel. function V. The display The appliance Turn the function control shows ”‰ . has been knob to the zero setting. automatically turned off. Error messages When the indicator displays an error message with “ , press the 0 sensor. The message will disappear. The set time function will be deleted. If the error message does not disappear, call the Technical Assistance Service. The following error messages can be solved by the user. Error message Possible ...
Otros modelos de este manual:Hornos - 3HB568XPE/02 (589.56 kb)
Hornos - 3HB568XPE/03 (589.56 kb)