Votos - , Puntuación media:
(
)
)
Fabricar: Apex Digital
Tamaño del archivo: 692.44 kb
Nombre del archivo: og_ls30_s1.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
The rubber feet provide increased stability and protection from scratches. 3. Select a convenient location – under a table, behind a sofa. Do not allow furniture or drapes to block the ventilation openings of the module. 4. Place it within reach of the audio input cable, speaker cables, and an electric outlet. 5. Aim the port (the round opening) into the room or along the wall to avoid blocking the port or creating too much bass. 6. For best bass performance, do not place the module so that the port is at equal distances from any two walls or from a wall and the ceiling. Music center Select a location for the music center. CAUTION: Be sure the three shipping screws on the bottom of the music center have been removed before proceeding. 1. Place the music center on a level surface. Allow enough room to lift the door and to access the headphone jack on the right side panel. 2. Place the music center close enough to the sound sources (TV, VCR, etc.) to allow for cable length. If you need additional audio and/or video cables to connect all of your components, see your dealer or call Bose® customer service. 3. Place the music center within 30 feet (9.1 m) of the Acoustimass module (the length of the audio input cable). AM193147_03_V.pdf December 20, 2001 Setting Up Setting Up CAUTION: Make sure all components are unplugged from the power outlet before you begin connecting the system. Figure 5 Speaker cable connection to the Jewel Cube speaker Connect the speakers and music center Once you have selected locations for your speakers and music center, connect the system. Connecting the Jewel Cube® speakers to the Acoustimass® module 1. Match each cable to the corresponding speaker location. • Front speaker cables have blue RCA connectors at one end, with L, R, or C molded into both the RCA connectors and the Jewel Cube connectors at the other end. • Surround speaker cables have orange RCA connectors at one end, with L or R molded into both the RCA connectors and the Jewel Cube connectors at the other end. 2. Insert the Jewel Cube connector of each cable fully into the jack on the rear of one of the five speakers (Figure 5). Match the ridge of the connector to the notch at the top of the jack. 3. Connect each cable to the corresponding jack on the Acoustimass module. a. Plug the blue connectors into the matching left front, center, and right front jacks. b. Plug the orange connectors into the matching left surround and right surround jacks. To lengthen the cable, connect speaker wire with male phono (RCA) plugs on each end to your supplied speaker cable. Use a female-to-female adapter (“barrel” connector). Or, splice in 18-gauge (.75 mm2) or thicker cord (connecting + to + and – to –). To purchase extension wire, see your dealer, electronics store, or call Bose® customer service. Connecting the Acoustimass module to the music center Connect the module to the music center with the audio input cable (Figure 6). 1. Plug the small black multi-pin connector (flat side facing up) into the jack marked SPEAKER ZONE 1 on the back of the music center. 2. Insert the right-angle multi-pin connector on the other end of the audio input cable into the AUDIO INPUT jack on the module. Align the connector at the angle shown in Figure 6. Note: Be sure that each connector is inserted completely into each jack. 3. Extend the audio input cable as much as possible, since it includes an antenna for the remote control. For information on connecting zone 2, see “Using two listening zones” on pages 23-24. December 20, 2001 AM193147_03_V.pdf Setting Up Setting Up Figure 6 Connecting the speakers and the music center L R TAPE IN L R TAPE OUT RIGHTRIGHT CENTER OUTPUTS TO CUBE SPEAKERS LEFT LEFT FRONTSURROUND AUDIO INPUT Right surround speaker Right front speaker Center speaker Right-angle connector into AUDIO INPUT Left front speaker Left surround speaker Audio input cablePower jackMulti-pin connector into SPEAKER ZONE 1 AC power pack Figure 7 Dual voltage Acoustimass module: voltage selector switch settings 230 V230 V 115 V115 V CAUTION: Make sure the voltage selector switch is set correctly. Figure 8 The AC power pack (model PS71 shown) CAUTION: Be sure to use the correct power pack for your area. Using the wrong one may damage your music center. Connecting the Acoustimass® module power cord 1. On a dual voltage Acoustimass module, the voltage selector switch is preset at the factory. If it is not set for the proper voltage, slide it to the correct setting (Figure 7). Use 115V for North America, and 230V for Europe and Australia. In Europe, use the adapter plug provided. If you are in doubt, contact your local electric utility for the appropriate voltage setting. 2. Plug the small end of the AC power (mains) cord into the module power jack. Note: Do not plug the power cord into a power outlet until you complete all connections. Connecting the music center power pack The Lifestyle® music center comes with either a 100V, 120V, 230V, or 240V power ...
Otros modelos de este manual:lector de DVD - AM193147_03_V. (692.44 kb)