. You can send the first page from the exposure glass then the remaining pages from the ADF. You cannot change from the ADF to the exposure glass. When transmitting from memory, see p.18 “Sending originals using the exposure glass”. When sending immediately, see p.24 “Sending originals using the exposure glass”. . When using the Internet Fax function, documents are sent at A4 width. Documents larger than A4 are reduced to A4 width. If the receiver's terminal is compliant with the T.37 full mode, documents are sent at the width specified in the Address Book. See p.53 “T.37 Full Mode”. . When setting bound originals (books, magazines, etc.), you can select to have either the left page or right page sent first with the User Parameters. See p.61 “Book Fax”, Facsimile Reference . See p.164 “User Parameters”, Facsimile Reference (switch 06, bit 6). Placing Originals Reference For how to place two-sided documents, see p.62 “Two-Sided Transmission (Double-Sided Transmission)”, Facsimile Reference . For acceptable types of originals, see p.204 “Acceptable Types of Originals”, Facsimile Reference . Setting a Scan Area Normally, a placed document is scanned according to the automatically detected size. If a scan area is specified, the document is scanned accordingly. Thus, documents can be sent without extra space or blank margins. See p.208 “Original sizes difficult to detect”, Facsimile Reference . . ....Auto Detect Detects the size of the first page and scans all pages using that size. Note . If the machine cannot detect the original size, a confirmation message appears. Replace the original. . ....Regular The placed document is scanned according to specified size regardless of actual size. The sizes that can be specified are A4KL, B4 JISL, A3L, 81/2".11"KL, 81/2".14"L, and 11".17"L. . ....Area Enter the area to be scanned. Only the area in the specified size is scanned regardless of the actual size of a placed document. See p.158 “Programming, Changing and Deleting a Scan Size”, Facsimile Reference . Note . To cancel the selected scan area, select [Auto Detect]. See p.14 “Specifying Auto Detect”. A AAAAPlace the originals, and then select any scan settings you require. Note . Small-size originals may be sent at a slight slant since they do not match the document guide. B BBBBPress [Scan Area]. C CCCCSelect the scan area. Specifying standard sizes APress [Regular]. Faxing B Press the size of the originals B Press [OK]. to be sent, and then press [OK]. Note .81/2".11" indicates LT. 81/2".14" indicates LG. 11".17" indicates DLT. CPress [OK]. “Area 1” or “Area 2” is shown above the highlighted [Scan Area]. Specifying Auto Detect A Make sure that [Auto Detect] is selected. The selected size is shown above the highlighted [Scan Area]. Specifying programmed sizes A Press [Area 1] or [Area 2]. If it is not, press [Auto Detect]. BPress [OK]. “Auto Detect” is shown above [Scan Area]. D DDDDSpecify a destination and press the { {{{{Start} }}}} key. Transmission Modes Transmission Modes There are two types of transmission: • Memory Transmission • Immediate Transmission . ....Memory Transmission Transmission starts automatically after the original has been stored in memory. It is a convenient method for when you are in a hurry and want to take the document away with you. You can also send the same original to several destinations. See p.19 “Broadcasting Sequence”. . ....Immediate Transmission Immediately dials the destination number, and while reading the original, sends it. It is very convenient when you want to send an original quickly or when you want to check the destination you are sending to. When using this type of transmission, the original is not stored in memory. You can only specify one address. Switching between Memory Transmission and Immediate Transmission Check the display to see which mode is currently active. You can change transmission mode by pressing [Immed. TX] or [Memory TX]. Note . You can select the transmission mode that is operative when the machine is turned on or mode are cleared , with [Memory / Immed. Transmission Switch] under Gen. Settings/Adjust. See p.143 “General Settings/Adjustment”, Facsimile Reference . Faxing Memory Transmission Memory transmission mode has standard fax, Internet Fax and IP-Fax. Important . If there is a power failure (the main power switch is off) or the machine is unplugged out for more than one hour, all the documents stored in memory are deleted. As soon as the main power switch is turned on, the Power Failure Report is printed to help you identify deleted files. If you turn only the operation switch off, documents are not deleted. See p.196 “Turning Off the Main Power / When a Power Failure Occurs”, Facsimile Reference . . We recommend you call the receiver and confirm with them when sending important messages...
)
