Votos - 4, Puntuación media: 3.5 ( )

Fabricar: Electrolux Tamaño del archivo: 486.74 kb Nombre del archivo: Idioma del manual:

This is acknowledged by pressing the button (Q). The power supply is then switched off. All activated functions are subsequently switched off: • Press the pre-set temperature button (TT) for some seconds. Lamp (LT) goes out. • Press the cooking time button (DT). Lamp (LD) goes out. • Switch off the control switch (S). Turn from position I to 0. Lamp (LS) goes out. • Switch off the power isolator (H) (only available as an option). • Turn from position I to 0. 0 = Off After cooking has been completed, the control switch (S) is switched off. • Turn from position I to 0. 0 = Off • The lamp (LS) goes out. • Switch off the power isolator (H) (only available as an option). Turn from position I to 0. 0 = Off The appliance can be switched off before cooking has been completed. If the function buttons (TT), (DT) and (ZT) are switched on and switching off is only done by means of the control switch (S), all the functions and previously set data for temperature, cooking time and starting time remain saved and active when the switch (S) is turned on again. IIf the appliance develops a fault, the electrical switch in the building must also be switched off and the gas valve must be closed. 4.5 Additional functions SOFT Pressing the Soft button (R) adapts the power supply to the food, i.e. reduces it. The lamp (LR) on the button (R) lights up if the soft setting has been switched on. The following functions are activated by pressing button (Q): 1. All displays Food temperature (AT) Cooking time (AD) Starting time (AZ) flash indicating the nominal value that has been programmed in. 2. Acknowledgement of the acoustic signal when cooking has been completed. 3. Acknowledgement of error messages (see section 12, Troubleshooting). TT LT DT LD ZT LZ LR Q R LS AT T AD D AZ Z LU LC C U S Button, activation of settings Lamp, cooking temperature Button, cooking time Lamp, cooking time expires Button, starting time Lamp, starting time Lamp, soft settings Button, acoustic signal Button, soft Lamp, temperature pre-setting Display, cooking temperature Temperature selection knob Display, remaining cooking time Cooking time knob Display, time Starting time knob Control switch Page 6 62.9695.01 OPERATING INSTRUCTIONS H Electrolux ZT Button, starting time LZ Lamp, starting time LR Lamp, soft settings Q Button, acoustic signal R Button, soft LS LC C U Fig. 4 Right console 4.6 Altering the pan settings Altering the nominal values while working All the nominal values programmed in originally can be easily altered during the working process by setting the buttons for temperature (T), for the cooking time (D) and for the starting time (Z) to the new values. When the buttons are turned, the nominal value will appear flashing on the relevant display. If the nominal value is not altered for a few seconds, the display reverts to the actual value. Altering the cooking programmes while working Switching off the button (TT) will interrupt the heating/cooking process. Switching off the cooking time button (DT) reverts to continuous cooking. Switching off the starting time button (ZT) deletes the programmed-in starting time. The appliance can be started manually. Cooking using the SOFT setting Normally (Soft setting deactivated), the food is heated up at maximum power and in the shortest possible heating-up time. This method of operation is suited to food with a high water content and which has good heat conductivity properties. When maximum power is used to heat them up, viscous, pasty and difficult to heat food (dairy products) tends to dry out along the heated surface of the pan, to turn dark and to burn. When the Soft setting is activated, the heating power is automatically adapted via the temperature difference to the type of food. Heating-up times are extended a little although the pre-set temperature is reached without the f...

Descargar ahora

Introduzca dos números de la imagen: