Further information can be obtained by referring to the U.S.A. National Fire Protection Association's NFPA96 regulations. These standards have also been adopted by the National Building Code in Canada. AIR SUPPLY Unit shall be located so as not to interfere with proper circulation of air within the confined space. All gas burners require sufficient air to operate. Large objects should not be placed in front of the unit which might obstruct the air flow through the front. Do not obstruct the flow

All units are equipped with fixed orifices and do not require primary air adjustment. LIGHTING INSTRUCTIONS NOTE: This appliance is equipped with a direct spark ignition system. Ensure gas and electrical supply to the appliance, are in the 'ON' position. 1. Turn the main manual gas shut-off valve to the 'ON' position. 2. Turn power switch to the 'ON' position. 3. Set thermostat to desired temperature. 4. If ignition fails and/or the control system goes into lockout, set power switch to the 'OFF"

The best time to clean is shortly after each use (allow unit to cool to a safe temperature). WARNINGS . Do not use detergents or cleansers that are chloride based or contain quaternary salt. Chloride Cleaners . Do not use a metal bristle brush or scraper. Wire Brush & . Steel wool should never be used for cleaning the stainless steel. Steel Pads . Unit should never be cleaned with a high pressure spray hose. High Pressure Spray Hose . Do not leave water sitting in unit when not in use. CLEANING

If the passive film of stainless steel has been broken, equipment starts to corrode. At its end, it rusts. Enemies of Stainless Steel There are three basic things which can break down stainless steel’s passivity layer and allow corrosion to occur. 1. Mechanical abrasion 2. Deposits and water 3. Chlorides Mechanical abrasion means those things that will scratch a steel surface. Steel pads, wire brushes and scrapers are prime examples. Water comes out of the faucet in varying degrees of hardness.

. . . . . . . . . . . . . .1 11. SK2489001 LIQUID TIGHT FITTING . . . . . . . . . . .1 12. SK2490600 FULL COUPLING S.S. . . . . . . . . . . . .1 13. SK2487800 BAYONET, ADAPTER . . . . . . . . . . . . .1 14. SK00409 SIDE BOX ASSEMBLY . . . . . . . . . . . .1 15. SK50963 BRACKET . . . . . . . . . . . . . . . . . . . . .1 16. SK50962 THERMOCOUPLE COVER . . . . . . . .1 17. F95 PALNUT . . . . . . . . . . . . . . . . . . . . . .91 18. FA11144 SCREW, S.S. 10-32 X 1/4 . . . . . . . .46 19. FA21008 HEX.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 41. FA11091 SCREW, 8-32 X 3/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 42. KE50473 GROUND LUG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 43. F900 K-LOCK NUT, 1/4-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 44. KE52936-8 FUSE, 1.25 AMP . . .

Improper installation of product could cause injury or damage. This equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are: UL, NSF, ASME/Ntl.Bd., CSA, ETL, and others. Many local codes exist, and it is the respunsibilrtjr'of'tbe^ owiier'-andr installer to comply with these codes. INSPECTION Before unpacking visually inspect the unit for evidence of damage during shipping. If damage is noticed, do not unpack the unit, follow shippi