Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Label Warning Unit Weight Part No.360188 BEFORE STARTING, MAKE SURE: TINE DEPTH CONTROL BAIL IS IN UP POSITION. TO START, MOVE ENGINE STOP SWITCH TO "ON" AND PULL ROPE. NOTE: IT MAY BE NECESSARY TO USE THE ENGINE CHOKE IF ENGINE IS COLD. PUSH FORWARD ON TINE LIFT HANDLE TO ENGAGE TINES IN GROUND. PUSH FORWARD ON OPERATOR’S BAIL TO ENGAGE DRIVE AND START AERATING. DURING OPERATION PUSHING DOWN ON OPERATOR’S HANDLE WILL MAXIMIZE CORING DEPTH. RELEASE BAIL TO STOP UNIT. NOTE: ENGINE WILL CONTINUE TO RUN WITH BAIL DISENGAGED. TO TURN UNIT, PULL BACK ON TINE LIFT HANDLE TO LIFT TINES OUT OF GROUND. GRADUAL TURNS CAN BE MADE WITHOUT LIFTING THE TINES. WITH TINES UP, PUSH FORWARD ON OPERATOR’S BAIL TO ENGAGE WHEELDRIVE FOR ASSISTED TURNING. TO STOP ENGINE MOVE ENGINE STOP SWITCH TO "OFF". ALL GUARDS ARE ATTACHED. USE ONLY A QUALIFIED MECHANIC T O SERVICE THIS MACHINE. INSPECT MACHINE BEFORE EACH USE AND REPLACE ANY WORN AND DAMAGED PARTS. CHECK ENGINE OIL DAILY. PROPERLY SECURE EQUIPMENT BEFORE TRANSPORTING. DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT. FOR PREVENTATIVE MAINTENANCE INSPECT AND CLEAN ENGINE AIR FILTER DAILY. REPLACE AS NEEDED. GREASE ALL BEARINGS AND CHECK GEAR REDUCTION OIL LEVEL ON EVERY ENGINE OIL CHANGE. ALWAYS: 360191 READ OWNERS MANUAL BEFORE OPERATING USE PERSONAL PROTECTION EQUIPMENT OPERATING INSTRUCTIONS ENGINE SPEED CONTROL Engine speed is set by using the throttle control lever, located in the middle of the operators handle. STOP START Increase Speed Decrease Speed STOP START Label Throttle Control Part No.810656 STOPSTARTIncrease Speed Decrease Speed Throttle lever on handle Throttle lever on handle Part No. 360178Page 4 of 12 Form No. F121203A 16 Operation 16 Operation INTENDED USE: This machine is designed for aerating established lawns and large grass covered areas. The machine should not be used for any other purpose than that stated above. DO NOT operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn tine reel, loose pulley bolts or set screws, loose engine or lodged foreign objects. (See trouble shooting section on page 12). Like all mechanical tools, reasonable care must be used when operating machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. STARTING ENGINE ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine must be level when checking and filling oil and gasoline. GEAR REDUCTION: See engine manufacturer’s instructions for type and amount of oil used. Engine must be level when checking and filling the gear reduction case. The engine is shipped from the factory with oil in the gear case. It shoudl be checked before first use. ENGINE SPEED: Controlled by throttle lever on the upper handle. Under normal conditions, operate at the minimum throttle speed to accomplish your task. NOTE: The unit ground speed varies with the engine speed. FUEL VALVE: Move fuel valve to "ON" position Honda: Located below the air cleaner on the engine. Briggs: Located on face of the engine. ENGINE STOP SWITCH: Move to "ON" position Honda only: Located on side of engine. During normal operation use the remote stop switch on the operators handle. CHOKE: Engage the choke when starting a cold engine. Honda: Located below the air cleaner on the engine. Briggs: Located on top of the air cleaner on the engine. THROTTLE: Move the throttle control on the upper handle to fast position. Pull starting rope to start engine. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 12. NOTE: Honda engines are equiped with a low oil sensor to prevent engine damage. When it senses a low oil condition (i.e. unit is operating or sitting on a steep slope) the engine shuts down. The low oil condition must be corrected before the engine can be restarted. See the engine owners manual for more information. TINES RAISING/LOWERING The tines are raised or lowered into the ground by operating the tine engagement lever on the upper handle. Tine penetration is very dependent on surface preparation. READ the operation section before aerating. TINES UP TRANSPORT AERATING OPERATION TINES DOWN RUNNING DO NOT-Use this machine on any surface other than a lawn or similar area. DO NOT-Use this machine on slopes in excess of 19°. DO NOT-Allow persons unfamiliar with this equipment to operate it. DO NOT-Allow children to operate this equipment. MOW: Mow the lawn to it's normal cut height. WATER: For the best performance and maximum tine penetration the lawn should be thoroughly watered the day before aeration. INSPECT lawn before begining work. Remove all rocks, wire, string, or other objects that can present a hazard during work prior to starting. IDENTIFY and mark all fixed objects to be avoided during work, such as sprinkler heads, water valves, buried cables, or clothes line anchors, etc. START ENGINE: See abo...
Otros modelos de este manual:cortadoras de césped - AE551, AE551H (761.94 kb)