Votos - 2, Puntuación media: 4.5 ( )

Fabricar: MTD Tamaño del archivo: 1.36 mb Nombre del archivo: Idioma del manual:

1) (712-0107) Hex Jam Nut 1/4-20 Thread (Qty-1) (712-0298) (Thinner Nut) I i I i I i I i I i I i I i I I I I I I I i I I I FIGURE 1. 0 INCHES ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, service engine with gasoline and oil as instructed in the separate engine manual packed with your unit. Nozzle Upper Handle^ FIGURE 2.-Loose Parts in Carton Air Duct Assembly Directional Discharge Assembly Impeller Guard Clutch Rod (Self-Propelled Models Only) -«5 H C—@ FIGURE 3.—Optional Tow Bar Kit Cupped // Washer Hand Knob Nozzle FIGURE 4. Upper Handle NOTE: Reference to right or left hand side of the vacuum is observed from behind the unit in the operating position. UNPACKING Remove the vacuum, loose parts, hardware pack and literature from the carton. Make certain all parts and literature have been removed before the carton is discarded. LOOSE PARTS IN CARTON See Figure 2) 1) Nozzle 1) Upper Handle 1) Air Duct Assembly 1) Clutch Rod (Self-Propelled Models Only) 1) Directional Discharge Assembly 1) Impeller Guard 1) Bag TOW BAR KIT Standard for push models, optional for self-pro-pelled models. -(See Figure 3) Hex Nut 5/16-18 Thread A (2) B (4) C (2) D (1) E (1) F (1) G (1) H (2) I (1) (2) Hex Nut 1/4-20 Thread Hex Jam Lock Nut 3/8-16 Thread ATTACHING THE NOZZLE (Hardware A) Place nozzle in position on front of housing so that it rests in flanges. Secure with one hand knob and cupped washer (cupped side of washer against the -nozzle). See figure 4. ATTACHING THE UPPER HANDLE (Hardware B) Place the upper handle in position over lower handle. Fasten with four hex bolts and lock nuts provided. -See figure 5. Two 7/16" wrenches are required. FIGURE 5 3 I Hand Knob Cupped .Washer Cupped Was her Thumb Screw ATTACHING THE AIR DUCT ASSEMBLY (Hardware A) Place air duct assembly over opening on top of housing. Secure front of air duct assembly with one flat washer, cupped washer (cupped side of washer against flat washer) and a hand knob. Secure back (close to engine) with one cupped washer (cupped side against air duct assembly) and thumb screw. See -figure 6. FIGURE 6. INSTALLING THE BAG (Hardware C) 1. Place the stud pins in holes in upper handle (head of pins go to the inside of handle). Secure pins with push-on speed nuts by holding speed nut with box wrench and tapping pin with ham--mer. See figure 7. FIGURE 7. Stud Pin On Handle 2. Assemble the bag by slipping the top straps on bag over upper handle. Hook two small straps over stud pins on handle. Slip elastic opening of bag over air duct assembly. Be certain elastic on bag is placed over the flanges on air duct assem-— bly. See figure 8. FIGURE 8. 4 Rod FIGURE 10. FIGURE 12. ATTACHING THE CLUTCH ROD (Hardware D) (Self-Propelled Models Only) 1. Assemble the clutch grip to the left hand side of upper handle. Secure in place with clevis pin and -hairpin clip. See figure 9. Head of clevis pin should be to the outside of handle. 2. Slide the extension spring onto clutch rod as -shown in figure 10. Thread hex lock nut onto clutch rod approximately 2-1/2 inches. 3. Hook top (hooked end) of clutch rod into upper hole on clutch grip. See figure 9. Hook spring into ■<-clutch bracket assembly. See figure 11. Adjust nut on the clutch rod so that when the clutch grip is all the way up, there is no slack in the spring. 4. Thread hex jam nut (thinner nut) onto clutch rod, and lock it against the lock nut. CONVERTING VACUUM TO A LEAF BLOWER A WARNING: Be sure to stop engine and disconnect spark plug wire. 1. Remove the bag. Remove the air duct assembly by removing the hand knob, cupped washer and flat washer from the front of the air duct assembly, and the thumb screw and cupped washer from behind the air duct assembly. Refer to figure 6. 2. Remove the nozzle by removing one hand knob and cupped washer. Refer to figure 4. 3. Remove the hand knob and cupped washer -which hold the housing to engine brace. See figure 12. 5 I 5. Lift up and out on the housing and rotate it 105° clockwise. Chute opening should be to the right hand side when viewed from the front of unit. See figure 13. Place the impeller guard into flanges on front of housing. Line up hole in guard with hole on housing. Secure with one hand knob and cupped washer (cupped side of washer against the impeller guard). See figure 13. Cupped Washer Flat Washer Place the directional discharge assembly over chute opening. Secure with one hand knob, cupped washer and flat washer, and the thumb screw and cupped washer. The cupped side of washer goes against the flat washer. See figure 14. Hand Knob FIGURE 14. Directional Discharge Assembly Truss Cupped Machine Washer (H) Hex Nut Screw (D) Hex Bolt (A) Shoulder Spacers (B) Lock Washer (E) yf' Shoulder Nut (F) Bo)t (G) FIGURE 15.—Optional Tow Bar INSTALLATION OF OPTIONAL TOW BAR 1. Remove the self-tapping screws on each si...

Descargar ahora

Introduzca dos números de la imagen: