QTY. DESCRIPTION 25 43910 21 Washer, Flat 3/16" 26 24798 4 Boot Mounting Strap 27 48133 1 Hard top Boot 28 44790 1 Poly Rear Door 29 43790 1 Strap, Tarp 25" 30 44849 4 "S" Hook, #32 31 44850 4 Strap, Tarp (Less Hooks) 32 23540 1 Hitch Plate 33 43866 20 Bolt, Hex 1/4-20 x 5/8" 34 43661 6 Bolt, Hex 1/4-20 x 1" 35 43088 45 Washer, 1/4" STD 36 1509-90 5 Bolt, Hex 1/4-20 x 1-1/4" 37 47189 43 Nut, Hex Nylock 1/4-20 38 47630 4 Screw, Self Tap 5/16-18 x 3/4" 39 23789 2 Door Latch 40 43351 1 Bolt, Hex 1/

Be aware of changing conditions on slopes. 1. Inspect the Mow-N-Vac to make sure all covers (rear door, vinyl boot, elbow, hose adapter (nozzle), hose and deck adapter are properly attached. 2. Check tires for proper inflation (12 - 14 lbs). 3. Check oil and gas in Mow-N-Vac engine. 4. Begin operation at low speed, adjusting forward speed to match grass height and/or moisture condition to prevent clogging. 5. Do not attempt to vacuum up any material other than vegetation found in a normal yard,

See figure 13. HINT: Push in on hex bolts as you tighten to form threads. 23. Connect the hose adapter to the engine housing by fastening three wing nuts to the pre-assembled bolts in the engine housing. See figure 13. 25. Place the hose hanger rod down into the hose hanger bracket on the impeller housing assembly. See figure 15. NYLON WASHERWING NUT5/16" X 3/4" HEX BOLT(SELF TAP) FIGURE 15 FIGURE 13 CLAMPHOSEHOSE ADAPTER(NOZZLE) 29. Assemble the hitch plate to the tractor hitch if: a. Your trac

Assemble a door latch at each end of the cross brace using a 5/16" x 3/4" hex bolt, a nylon washer and a 5/16" Nylock hex nut. Place the nylon washer between the door latch and cross brace. Tighten so that latch is snug but will still rotate. See figure 13. 20. Place a side panel on top of the cart bed flange, inside the lip of the front panel. Fasten the side panel to the front panel using three 1/4" x 5/8" hex bolts and 1/4" Nylock hex nuts. Fasten the side panel to the cart bed flange using t

Do not operate on slopes in excess of 10 degrees. STAY OFF STEEP SLOPES. • Follow the maintenance instructions outlined in this manual. Look for this symbol to point out important safety precautions. It means — Attention!! Become alert!! Your safety is involved. DANGER: This Mow-N-Vac was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This unit is c

• Mantenga la barredora alejada del fuego. El calor excesivo puede danar los cepillos y la bolsa de la tolva y causar el incendio de la bolsa y su contenido. • Antes de guardar la barredora, siempre vacie la bolsa de la tolva para evitar la combustion espontanea de su contenido. • Siga las instrucciones de lubricacion y mantenimiento como se senalan en la seccion de mantenimiento de este manual. InsTruCCIones De armaDo armaDo De la BarreDora De 44 PulGaDas 1. Deslice los canales del brazo de la

Retire toda la ferreteria y todas las partes sueltas de la caja y verifique que todas las partes y sujetadores que se muestran en las paginas 2 y 3 han sido incluidos. ESPANOL ARMADO DE LA BARREDORA Nota: La mano derecha y la izquierda se determinan desde la posicion del operador sentado en el vehiculo de arrastre. Nota: las figuras del armado se encuentran en las paginas de 5 a 10. 1. (Figura 1) Fije la mensula de angulo en la carcaza de la barredora usando un perno hexagonal (F) y una tuerca d

No. Part No. Qty. Description Ref. No. Part No. Qty. Description 1 48646 1 Hitch Tube, R.H. 42 43661 4 Bolt, Hex 1/4-20 x 1" Lg. 2 48645 1 Hitch Tube, L.H. 43 25102 2 Dust Cover 3 24950 1 End Plate, R.H. 44 48471 2 Tube, Hopper Frame (Rear) 4 24951 1 End Plate, L.H. 45 48467 2 Tube, Upper Hopper Frame (Front) 5 24989 1 Wrapper 46 48728 2 Tube, Lower Hopper Frame (Front) 6 43175 2 Bolt, Hex 1/4-20 x 1/2" Lg. 47 48402 4 Plastic Plug 7 C-9M5732 6 Rivet, Pop 48 48396 1 Hopper Bag 8 23887 1 B