Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Desa Tamaño del archivo: 1.15 mb Nombre del archivo: 114683-01.pdf Idioma del manual:

The equipment shutoff valve is for turning on or shutting off the gas to the appliance. Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas. Install sediment trap in supply line as shown in Figure 15, page 13. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly. External Regulator Propane/LP Supply Tank Vent Pointing Down Figure 14 - External Regulator With Vent Pointing Down 114683-01B INSTALLATION Continued IMPORTANT: Hold the pressure regulator with wrench when connecting it to gas piping and/or fittings. Do not over tighten pipe connection to regulator. The regulator body could be damaged. Pressure WARNING: Never use an open flame to check for a leak. Applyanoncorrosiveleakdetection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once. CAUTION: For propane/LP gas, make sure external regulator has been installed between propane/LP supply and heater. See guidelines under Connecting to Gas Supply, page 12. Tee Joint Reducer Bushing to 1/8" NPT 1/8" NPT Plug Tap 3/8" NPT Pipe Nipple Heater Cabinet Equipment Shutoff Valve* 3" Min. Natural Gas From Gas Meter Ground Joint Union Tee Joint Pipe Nipple 1. Disconnect appliance with its appliance main Regulator Test Gauge Connection* PRESSURE TESTING GAS SUPPLY PIPING SYSTEM Test Pressures In Excess Of 1/2 PSIG (3.5 kPa) Sediment Trap gas valve (control valve) and equipment shutoff valve from gas supply piping system. Pressures in excess of 1/2 psig will damage heater regulator. 2. Cap off open end of gas pipe where equipment Cap (4" W.C. to 10.5" W.C. Pressure) 3. shutoff valve was connected. Pressurize supply piping system by either Propane/LP From External Regulator (11" W.C. to 14" W.C. Pressure) Figure 15 - Gas Connection * ACSAdesign-certifiedequipmentshutoffvalve with 1/8" NPT tap is an acceptable alternative to test gauge connection. Purchase the optional CSA design-certified equipment shutoff valve from your dealer. See Accessories, page 30. CHECKING GAS CONNECTIONS WARNING:Testallgaspiping and connections, internal and external to unit, for leaks after installing or servicing. Correct all leaks at once. opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air. 4. Check all joints of gas supply piping system. Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks. Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Figure 16). Open Equipment Shutoff Valve Closed Figure 16 - Equipment Shutoff Valve 114683-01B INSTALLATION Continued 2. Pressurize supply piping system by either opening propane/LP supply tank valve for propane/LP gas or opening main gas valve located on or near gas meter for natural gas or using compressed air. 3. Check all joints from gas meter for natural gas (see Figure 17) or propane/LP supply tank for propane/LP gas, to equipment shutoff valve (see Figure 18). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 4. Correct all leaks at once. PRESSURE TESTING HEATER GAS CONNECTIONS 1. Open equipment shutoff valve (see Figure 16, page 13). 2. For natural gas open main gas valve located on or near gas meter. For propane/LP gas open propane/LP supply tank valve. 3. Make sure control knob of heater is in the OFF position. 4. Check all joints from equipment shutoff valve to thermostat gas valve (see Figure 17 or 18). Apply a noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. 5. Correct all leaks at once. 6. Light heater (see Operating Heater, starting on page 15). Check all other internal joints for leaks. 7. Turn off heater (see To Turn Off Gas to Appliance, page 16 or 17, depending on your model heater). 8. Replace front panel. Thermostat Gas Valve Equipment Shutoff Valve Gas Meter Figure 17 - Checking Gas Joints for Natural Gas Thermostat Gas Valve Equipment Shutoff Valve Propane/LP Supply Tank Figure 18 - Checking Gas Joints for Propane/LP Gas 114683-01B OPERATING HEATER MANUAL CONTROL MODELS FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these ...

Descargar ahora

Introduzca dos números de la imagen: