Optional High Wind Termination Cap Secure Flashing with Non-Hardening Sealant and Roofing Nails Figure 5.15 Step 9. Twist-lock the vent cap and seal. Note: For multi-story vertical installations, a ceiling firestop is required at the second floor, and any subsequent floors (Figure 5.16). The opening should be framed to 10 in. x 10 in. (254mm x 254mm) inside dimensions, in the same manner as shown in Figure 5.13 on page 16. MIN. 1 in. (25mm) CLEARANCE CEILING FIRES TOP NAILS MIN. 1 in. (25mm) CLE

Vent system termination is permitted in porch areas with two or more sides open. You must follow side wall, overhang and ground clearances as stated in the instructions. Quadra-Fire assumes no responsibility for the improper performance of the appliance when the venting system does not meet these requirements. NOTE 3: Location of the vent termination must not interfere with access CAUTION: IF EXTERIOR WALLS ARE FINISHED WITH VINYL SIDING, Figure 4.4 IT IS SUGGESTED THAT A VINYL PROTECTOR KIT BE

Do NOT use gasoline, lantern fuel, kerosene, charcoal lighter fluid or similar liquids in this appliance. Combustible materials may ignite. E. Frequently Asked Questions ISSUE SOLUTIONS Condensation on the glass This is a result of gas combustion and temperature variations. As the appliance warms, this condensation will disappear. Blue flames This is a result of normal operation and the flames will begin to yellow as the appliance is allowed to burn for 20 to 40 minutes. Odor from appliance When

Fuel Conversions Before making gas connections ensure that the appliance being installed is compatible with the available gas type. Any natural or propane gas conversions necessary to meet the appliance and locality needs must be made by a qualified technician using Hearth & Home Technologies specifi ed and approved parts. 1. Converting to LP Gas Figure 6.2the wire clip. Pull off pilot hood and set aside. Do not remove MILLIVOT GENERATOR THERMOCOUPLE PILOT HOOD ALIGNMENT NOTCH NOTE: Gas conversi

• Heat & Glo • Bravo • 704-902 Rev. F • 10/08 Note: The following requirements reference various Massachusetts and national codes not contained in this document. Inspection The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless, upon inspection, the inspector ob- H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or stru

D. DO NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. For use with natural gas and propane. A conversion kit, as supplied by the manufacturer, shall be used to convert this appliance to the alternate fuel. Also Certified for Installation in a Bedroom or a Bedsitting Room. For assistance or additional information, consult a

Flat to 6/12...........................................................1.0* Over 6/12 to 7/12.................................................1.25* Over 7/12 to 8/12.................................................1.5* Over 8/12 to 9/12.................................................2.0* Over 9/12 to 10/12...............................................2.5 Over 10/12 to 11/12.............................................3.25 Over 11/12 to 12/12.............................................4.0 Over

This minimizes the effects of wind turbulence. • Be located away from trees, adjacent structures, uneven roof lines and other obstructions. Offsets can restrict draft so their use should be minimized. Consider the fi replace location relative to fl oor and ceiling and attic joists. Recommended Location Marginal Location Location Not Recommended Recommended Location Location NOT Recommended Multi-level Roofs Windward Leeward 5 55 Framing and Clearances A. Selecting Appliance Location When selecti

Heat & Glo • GEM42 • 371-900 Rev. N • 2/05 Figure 26. Intermittent Pilot Ignition (IPI) Wiring Diagram NOTE 1: Ignition module, valve, pilot and wall switch operate on 3 volts. 120 VAC is required at junction box unless equipped with battery back-up. NEUTRAL GROUND REMOTE CONTROL HOT LOW VOLTAGE SEE NOTE 1 ON/OFFWALL SWITCH VALVE BROWN BROWN RED ORANGE GREEN BLACK OPTIONAL BATTERY BACK-UP ORANGE (IGNITOR) WHITE (SENSOR) BLACK GROUND TO FIREPLACE CHASSIS PILOT ASSEMBLY AND VALVE ASSEMBLY MUST BE