Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
32-1). HEX NUT 2 GA TERMINAL LUG INPUT BRACKET LONG POWER CABLE EXTERNAL TOOTH LOCK WASHER PROTECTIVE COVER FIG. 32-1 5. Route the interlock cable from safety interlock system on the vehicle, underneath vehicle floor and through the grommet, and up to the Lift (FIG. 32-2). If possible, use the same cable routing as the long power cable installed in previous steps. Secure the interlock cable every 8”-10”. INTERLOCK CABLE 6. Make sure interlock cable will reach INTERLOCK WIRE the white-red stripe wire (interlock (SIGNAL FROM signal from vehicle) and the brown VEHICLE) wire (interlock signal to vehicle) on the Lift (FIG. 32-2). Signal may INTERLOCK WIRE be ground or V+. Connect the inter-(SIGNAL TO VEHICLE) lock wires from the vehicle interlock system to the white-red stripe wire and brown wire on the Lift (FIG. WHITE-RED STRIPE BROWN WIRE 32-2). (FROM LIFT) WIRE (FROM LIFT) FIG. 32-2 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 PATENTS PENDING 32 VEHICLE FRAME 3/8” LOCK WASHER 3/8”-16 X 1” LG. CAP SCREW TERMINAL LUG VEHICLE FRAME 3/8” LOCK WASHER 3/8”-16 X 1” LG. CAP SCREW TERMINAL LUG 7. Uncoil the ground cable from the bottom of the pump cover. Route the ground cable on the Lift through grommet in vehicle floor (FIG. 33-1A & 33-1B). GROMMET GROUND CABLE NOTE: Apply dielectric grease to all electrical connections. 8. Extend the ground cable to reach vehicle frame (FIG. 33-2). Connect to an existing grounding point if available. If necessary, drill a 13/32” (0.406”) hole in vehicle frame for bolting the ground cable terminal lug (FIG. 33-2). 3/8”-16 GROUND HEX NUT CABLE 9. Bolt the ground cable terminal lug to vehicle frame as shown in FIG. 33-2. BOLTING GROUND CABLE TO VEHICLE FRAME FIG. 33-2 11921 Slauson Ave. Santa Fe Springs, 90670 (800) 227-FAX (888) NOTE: Clean the ground cable connection point on the frame down to bare metal. NOTE: If there is a grounding point on the frame, use it to connect ground cable. Skip step 8. GROUND CABLE ROUTED FROM LIFT FIG. 33-1A BARE METAL 33 PATENTS PENDING ROUTE/CONNECT CABLES & HAND PENDANT - Continued CAUTION! To prevent vehicle access door from pinching and damaging the hand pendant cable, secure cable away from the door frame. Also, be sure that the hand pendant cable does not interfere with or bind against moving parts. 10. Connect the hand pendant cable as follows. Feed the cable through the hole located in the main frame (FIG. 34-1). Secure cable strain relief to main frame with plastic nut (FIG. 34-1). Next, connect hand pendant connector to wiring harness (FIG. 34-1). WIRING HARNESS MAIN FRAME STRAIN RELIEF HAND PENDANT CONNECTOR HEX NUT CONNECTOR CONNECTING HAND PENDANT CABLE (RH SIDE CONNECTION SHOWN) FIG. 34-1 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 PATENTS PENDING 34 11. Find accessible place on vehicle wall or wheelchair door (near Lift) to place the hand pendant hanger and cable hook (FIG. 35-1). HAND PENDANT & HANGER CABLE HOOK PUMP COVER TYPICAL LOCATION (INSIDE VEHICLE) FOR STOWING HAND PENDANTFIG. 35-1 11921 Slauson Ave. Santa Fe Springs, 90670 (800) 227-FAX (888) 35 PATENTS PENDING ROUTE/CONNECT CABLES & HAND PENDANT - Continued 11921 Slauson Ave. Santa Fe Springs, CA. 90670 (800) 227-4116 FAX (888) 771-7713 12. Place decals (from Parts Box) on the vehicle, near the hand pendant (typical place- ment shown in FIG. 36-1). Make sure decals are visible to operator when Lift is being operated. DECALS AND HAND PENDANT MOUNTING ON VEHICLE FIG. 36-1 DOOR HAND PENDANT & HANGER MOUNTING CABLE HOOK DECAL “A” P/N 268303-01 DECAL “A” DECAL “C” DECAL “I” DECAL “J” DECAL “B” DECAL SET FOR WL7-vers.C DECAL SET FOR WL7-vers.C-1K P/N 267620-02 P/N 267620-04 FIG. 36-2 FIG. 36-3 PATENTS PENDING 36 13. Connect short power cable to vehicle POSITIVE (+) BATTERY SHORT POWER TERMINAL CABLE battery as follows. Remove nut from BOLT positive (+) battery terminal connector (FIG. 37-1). Connect the power cable. Reinstall nut. NUT CONNECTING POWER TO LIFT (TYPICAL) FIG. 37-1 11921 Slauson Ave. Santa Fe Springs, 90670 (800) 227-FAX (888) 14. Turn ON power ON/OFF switch on pump cover to power the Lift (FIG. 37-2). The POWER light on hand pendant should be illuminated (FIG. 37-3). Briefly press the FOLD button on hand pendant (FIG. 37-3) to pressurize hydraulic system. Then, remove remaining shipping straps. POWER ON/OFF SWITCH STOWED LIFT - LH SIDE SHOWN FIG. 37-2 UP FOLD FOLD UNFOLD POWER LIGHT HAND PENDANT FIG. 37-3 37 PATENTS PENDING ROUTE/CONNECT CABLES & HAND PENDANT - Continued 15. Press the UNFOLD button on hand pendant to unfold Lift (FIG. 381). Platform lights will turn on when PLATFORM LIGHT platform is at fl oor level. (2 PLACES) LIFT AT FLOOR LEVEL FIG. 38-1 16. Next, press DOWN button on hand pendant. When the platform reaches the ground, the outboard rollstop will automatically open to ramp position (FIG. 38-2). GROUND 17. Install the remaining bolts, lock nuts, and under-vehicle supports supp...
Otros modelos de este manual:Sillas de ruedas - WL7-VERS. C-1K (1.69 mb)