Votos - , Puntuación media:
(
)
)
Fabricar: Pride Mobility
Tamaño del archivo: 2.39 mb
Nombre del archivo: US_Jazzy_600_XL_om.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
Repeat this test three times, pushing the joystick backwards, then left, and then right. Monthly Checks • Check for drive tire wear. See your authorized Pride Provider for repair. • Check the caster wheels for wear. Replace them as necessary. • Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings replaced. See your authorized Pride Provider for repair. • Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc. Yearly Checks Take your power chair to your authorized Pride Provider for yearly maintenance. This helps ensure that your power chair is functioning properly and helps prevent future complications. Storage Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries from the power chair. See VI. “Batteries and Charging.” Jazzy 600 XL Jazzy 600 XL 37 V I I I . C A R E A N D M A I N T E N A N C E WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be damaged. Cleaning Instructions WARNING! Never hose off your power chair or place it in direct contact with water. Your power chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth. WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become slippery or dry out and crack. Use soapy water and dry the seat thoroughly. Tire/Wheel Replacement If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid tire insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through your authorized Pride Provider. WARNING! To avoid possible injury, be sure that the controller’s power is turned off and the power chair is not in freewheel mode before performing this procedure. WARNING! Completely deflate the tire before attempting repair. Follow these easy steps for a quick and safe repair for both pneumatic and solid tires: 1. Turn off the power to the controller. 2. Set the power chair up on blocks. 3. If you are changing a pneumatic tire, completely deflate it before removing the wheel. 4. Remove the drive wheel nut and washer from the wheel hub. See figure 26. 5. Pull the wheel off the axle. 6. Remove the screws that fasten the two rim halves together. See figure 27. 7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire. 8. Screw together the two rim halves. 9. Slide the wheel back onto the shaft. Make sure that the key is in the axle slot. 10. Reinstall the drive wheel nut and washer onto the wheel hub and tighten. Figure 27. Jazzy 600 XL Drive Wheel Disassembled 11. Inflate the pneumatic tire to 35 psi (2.4 bar) (if equipped with pneumatic tires). 12. Remove the power chair from the blocks. Figure 26. Jazzy 600 XL Drive Wheel TIRE REAR RIM HALF FRONT RIM HALF TUBE SCREWS DRIVE WHEEL NUT WASHER V I I I . C A R E A N D M A I N T E N A N C E VIII. CARE AND MAINTENANCE Battery Replacement A battery wiring diagram is printed on a decal located on the front battery tray. See VI. “Batteries and Charging” for correct battery specifications. WARNING! Prevent injury. Do not replace battery when seat is occupied. WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves when handling batteries and wash hands after handling. WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that much weight, be sure to get help. Lifting beyond your capacity can result in personal injury. To replace the batteries: 1. Turn off the power to the controller. 2. Make sure that the power chair is in drive mode. See III “Your Power Chair.” 3. Loosen the rear shroud fasteners and remove the rear shroud. See figure 28. 4. Disconnect the battery harness from the rear battery. 5. Remove the retaining pin and lift off the front cover using the foot platform bracket. See figure 17. 6. Slide the battery tray forward. 7. Disconnect the battery harness from the front battery. 8. Undo the hook and loop straps from both batteries. 9. Remove the batteries. 10. Replace with new batteries. 11. Fasten the hook and loop straps around both batteries. 12. Connect the battery harness to the front battery according to the battery wiring diagram. See figure 28. WARNING! Prevent injury. Make sure you tighten the fasteners so that the connections are secure. 13. Slide the battery tray back into the power base. 14. Connect the battery harness to the rear battery. 15. Reinstall the front cover. 16. Reinstall the rear shroud and tighten the rear shroud fasteners. 17. Charge the batteries. See VI. “Batteries and Charging.” Jazzy 600 XL Jazzy 600 XL 39 BATTERY W...