Votos - 2, Puntuación media: 4 ( )

Fabricar: MTD Tamaño del archivo: 1.48 mb Nombre del archivo: Idioma del manual:

Keep where gasoline fumes will not reach an open flame or spark. For long periods of storage, refer to the “Off-Season Storage” section of this manual. T ASSEMBLY INSTRUCTIONS ATTACHING THE LOWER |A LEAF RAMP SECTION Hex Bolt -5/16-18 x 8-3/8" Long Flat Washer 5/16" I.D Hex Lock Nut 5/16-18 Thread B IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: To determine right and left hand sides of your shredder, stand behind and face the hopper (engine is at the front of the unit). Your shredder has been completely assembled at the factory, except for the hopper, lower and upper leaf ramp sections, chute deflector and the catcher bag. The hardware pack and safety glasses are also included in the carton. The hardware pack contains the parts shown in figure 1 (shown full size). TO REMOVE SHREDDER FROM CARTON Cut the corners of the carton. Remove all packing inserts. Roll shredder out of carton. Make certain all parts and literature have been removed before the carton is discarded. TOOLS REQUIRED FOR ASSEMBLY (1) Phillips Screwdriver (2) 1/2" Wrenches (one must be a socket wrench) (2) 7/16" Wrenches or Adjustable Wrenches ATTACHING THE UPPER LEAF RAMP SECTION 3 Spacers (Inside Hinge) Housing Assembly Hex Bolt Chute deflector A WARNING: Make certain the spark plug wire is disconnected and moved away from the spark plug before assembling the shredder. ATTACHING THE CHUTE DEFLECTOR (See Figure 2) 1. 2. FIGURE 2. Lower Lea F Ramp Sc ction Hex Bolt 8-3/8" Long Flat Washer Hex Lock Nut FIGURE 3. Hopper Self-Tapping Screws FIGURE 4. 4. 5. A Remove the hand knobs and cupped washers from each side of the discharge opening on the left side of the shredder. Remove the hex lock nut, two spacers and hex bolt from inside the hinge on the housing assembly. Do not remove one spacer from the hex bolt. Place the chute deflector in position on the discharge opening on the left side of the shredder. Insert hex bolt and spacer through hinge on chute deflector and housing (spacer fits inside of hinge). Place the second spacer over the hex bolt, inside the other part of the hinge. Secure with hex lock nut. Tighten securely. Secure both sides of the chute deflector to the housing using the hand knobs and cupped washers (cupped side of washers go against the chute deflector). WARNING: Do not operate this chipper-shredder unless the chute deflector has been properly installed and is secured with the hand knobs. -ATTACHING THE LOWER LEAF RAMP SECTION (Hardware A) Insert hex bolt 8-3/8" long through lower leaf ramp section and frame. Secure with flat washer 5/16" I.D. and hex lock nut. Make certain the edges of the lower leaf ramp section are underneath the stop washers. See figure 3. Plastic insert in hex nut should face away from lower leaf ramp section. Tighten hex nut until parts are snug, but so lower leaf ramp section can still be rotated on the frame. ATTACHING THE HOPPER When attaching the hopper, first remove the five selftapping screws from the frame of the unit. Place the -hopper in position on the shredder. See figure 4. Start all five self-tapping screws, then tighten securely using a 1/2" socket wrench. ATTACHING THE UPPER LEAF RAMP SECTION (Hardware B) Place the edge of upper leaf ramp section inside the lower leaf ramp section. Secure with four truss machine screws and hex lock nuts. The heads of the truss machine screws should be to the inside of the upper leaf ramp section. Start all screws and nuts, -then tighten securely. See figure 5. 4 Catcher Bag ATTACHING THE CATCHER BAG Your shredder is equipped with a catcher bag to catch the shredded material. To attach the bag, place the opening of the bag over the chute deflector so it completely covers the chute opening. Depress the plunger on the drawstring, pull on the drawstring until the bag is tight around the chute opening. Release plunger to lock it into position. 'See figure 6. FIGURE 6. OPERATION KNOW YOUR SHREDDER READ THIS OWNER’S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR SHREDDER. Compare the illustrations with your shredder to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. OPERATING CONTROLS (See figure 7) RELEASE BAR—Used to release the leaf ramp when raising or lowering. CHOKE LEVER—Used to enrich the fuel mixture in the carburetor when starting a cold engine. STARTER HANDLE—Used to manually start the engine. THROTTLE CONTROL—Controls engine speed and stops the engine. The operation of any shredder can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields. We recommend wide vision safety mask for over spectacles or standard safety glasses. 5 I BEFORE STARTING 1. Place the shredder on a firm, level surface. 2. Attach spark plug wire to spark plug. 3....

Descargar ahora

Introduzca dos números de la imagen: