Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
The highlighted channels also indicated those channels available in the “basic” mode (default). All channels can be accessed when in the “expanded” channel mode (see page 8 for more information). Wideband frequencies in highlighted rows. Setup Instructions Specifications Quick Reference Package Contents Package Contents Compatibility Charts Compatibility ChartsCompatibility Charts 16 Phonak Frequency Chart Frequency (MHz) Listen Phonak 216.012 1A 1 216.025 2A 41 216.037 3A 2 216.062 1B 21 216.075 2B 42 216.088 3B 4 216.113 1C 5 216.125 2C 43 216.137 3C 22 216.162 1D 23 216.175 2D 44 216.188 3D 8 216.213 1E 9 216.225 2E 45 216.238 3E 24 216.262 1F 25 216.275 2F 46 216.287 3F 12 216.312 1G 13 216.325 2G 47 216.338 3G 26 216.363 1H 27 216.375 2H 48 216.387 3H 16 216.412 1J 17 216.425 2J 49 216.438 3J 18 216.512 1K 61 216.525 2K 29 216.537 3K 62 216.562 1L 28 216.575 2L 52 216.588 3L 64 216.613 1M 65 216.625 2M 53 216.637 3M 81 216.662 1N 82 216.675 2N 54 216.688 3N 68 216.713 1P 69 216.725 2P 55 216.738 3P 83 216.762 1R 84 216.775 2R 56 216.787 3R 72 216.812 1S 73 216.825 2S 57 216.838 3S 76 216.863 1T 85 216.875 2T 58 216.887 3T 86 216.912 1U 77 216.925 2U 59 216.938 3U 88 216.963 1V 79 216.975 2V 60 216.988 3V 80 Wideband frequencies are indicated in highlighted rows. The highlighted channels also indicated those channels available in the “basic” mode (default). All channels can be accessed when in the “expanded” channel mode (see page 8 for more information). Specifications Setup Quick Package Contents Package Compatibility Charts Compatibility 17 18 InformationSetup InstructionsQuick ReferenceSpecificationsPackage ContentsPackage ContentsInformation LT-800 Troubleshooting Troubleshooting The LT-800 has no power Make sure the LA-207 power supply is connected to a power source and is connected to the jack marked “Power Input”. Make sure the POWER button is pressed in. There is no audio or the audio level is too low Make sure that your audio source is properly connected to Input 1 and/or Input 2. The Input 1 or Input 2 switches must be in the correct position for the appropriate input level. For example: if you are using the output of a mixer on Input 2, the switch should be in the -10dBu position. If it were to be in the +10dBu position, the level would be too low. Also, check the Input knob to ensure it is properly adjusted. You should be able to see the VU meter deflect on Input 1 or Input 2 corresponding with the input level of the audio source. You can listen to the audio source by connecting a headset to the front panel jack and adjusting the Monitor volume control. If the level of audio into the transmitter is low and can’t be corrected using the level input switches, the audio processor can be turned on to boost the signal (see page 8 to set, page 12 for description of Process Mode). The audio is distorted Check to make sure you have the input level select switches in the proper position. You may be providing too much audio level for the input stage to handle. Make sure the SQ mode is set correctly on both the LT-800 and the receivers you are using. If your receivers do not have SQ, make sure the SQ mode is turned off (see page 8). There is hum in the audio Make sure you have properly grounded the audio source to the LT-800. Check the connections from the audio source to the LT-800. If you can, try to use a balanced audio source -this will reduce the chance of creating hum. Connect a ground wire from the LT-800 to ground and/or to the ground of the source audio. There is a tone The Test Tone button has been pressed (its LED light is on). Push the Test Tone button to turn off the tone. The Audio Input 1 sounds “tinny” If you are using an unbalanced audio source, make sure Pin 3 on the XLR or the ring on the .” plug is grounded (see page 9). I cannot pick up the signal on the receiver Check to make sure the receiver and the transmitter are using the same frequency band (i.e. 72 MHz or 216 MHz) and that they are on the same channel. Make sure the LT-800 has an antenna connected. Ensure that the receiver has an antenna (for portable products the headset is the receiving antenna). I can pick up the signal on the receiver, but it sounds like it’s not tuned in Check to make sure the transmitter and receiver are on exactly the same channel. It’s a good idea to lock the channels once they have been set. To lock the LT-800, press the UP button for 3 seconds (see page 10). InformationSetup InstructionsQuick ReferenceSpecificationsPackage ContentsPackage ContentsInformation LT-800 Troubleshooting Troubleshooting The LT-800 has no power Make sure the LA-207 power supply is connected to a power source and is connected to the jack marked “Power Input”. Make sure the POWER button is pressed in. There is no audio or the audio level is too low Make sure that your audio source is properly connected to Input 1 and/or Input 2. The Input 1 or Input 2 switches must be in the correct position for the appropriate input level....
Otros modelos de este manual:Eléctrico - NOT FLJ LT-800-072 (4.87 mb)