Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code ANSI Z223.1. *Available from the American National Standards Institute, Inc., 11 West 42nd St., New York, N.Y. 10036. DO consult your dealer and local gas supplier about qualified installers and servicemen. DO refer to your Empire Installer and Serviceman's Manual so that you can make sure that all installation and service work was done properly. You bought the best furnace, now make sure you get the best service. DO make sure your venting system and flue pipe were installed as outlined in your Empire Installer and Serviceman's Manual. DO see "Using Your Furnace" before you try to light the pilot or turn your furnace on. DO see "Using Your Furnace" for instructions on how to set the register temperature control when children are present. CAUTION Floor register becomes hot when operating and can cause burns. Keep children off! DON'T adjust or repair the combination valve, and don't take it apart. DON'T try to make any repairs except the ones listed for you to do in Service Checks. DID YOU GET EVERYTHING? After you have unpacked your Empire furnace, you should make certain everything is in order. For example, did you receive the model furnace you ordered? Is it the model for the type of gas (Natural or Propane) you want? Did you get all of the parts you are supposed to have? Look at picture A. It will tell you where your furnace identification plate is. The plate has stamped on it the model and serial number of the furnace you received. It also tells if your furnace is supposed to use natural (NAT) or propane (LP) gas. See if the serial number on your furnace is the same as the number on the WARRANTY CARD. Be sure your dealer fills out the WARRANTY CARD, then MAIL the purchaser's report (bottom part) to us. Look at Picture A and also the list below to see if you have received everything on the list. If anything is missing or broken, or if the model or serial numbers are not right, or if the furnace is for natural and you have propane (or the other way around), contact your dealer or Empire Comfort Systems, Inc. A 1. Owner's manual (you are reading it now) 2. Installer and Serviceman's Manual 3. Wall thermostat (packed in draft diverter carton) 4. Draft diverter (packed in separate carton) 5. Cardboard cutout template (inside top of furnace box) 6. Register (top of furnace) 7. Warranty card 8. Debris pan 9. Lighting rod (inside furnace lying on bottom) 10. Inner casing (inside furnace) HOW YOUR FURNACE WORKS HEATING Your Empire furnace uses air from two places; air from outside the living area, and air from inside the living area. The air from outside the living area is mixed with gas and burned inside a chamber in your furnace. The burned gas and air is exhausted through a flue pipe to the outside air again. This exhaust should not be permitted to enter the living area. Burning gas inside the furnace chamber makes the chamber hot. Cool air from inside the living area is drawn into the furnace and flows past the outside of the hot chamber. The chamber makes this air hot and this hot air flows out of the furnace and back into the living area. When enough air in the living area has been heated, the thermostat turns the furnace off automatically. Picture B shows the flow of air inside and air outside the living area. You can see that the air inside is not mixed with air outside the living area. The furnace does not burn air that is within your living area, and burned air or exhaust should not enter the living area. Page 4 R-1842 INSULATED VENT ENCLOSURE Vented floor furnace installed with the vent going directly to the outside and above the eaves can cause poor venting. The cold vent pipe will have a delay in proper venting and cause spillage of flue products at the draft diverter. The spillage of flue products can result in pilot outage due to recirculation of flue products into the main burner, also, condensation can occur in the vent pipe which can cause an ice build-up or rusting of the draft diverter. To prevent delayed venting as well as condensation of flue products an insulated vent enclosure is recommended. Use Type B vent pipe and maintain at least a one inch clearance to combustibles. Use metal thimble to protect vent pipe as it passes through combustibles. VENTING Good venting is essential to good dependable heat. Venting removes the exhaust that results when gas is burned inside your furnace. If the exhaust is not vented away, the exhaust may gather under your house and could seep into the house and be fatal. Venting is done through a vent pipe (chimney) which, when correctly installed, causes a draft (suction) at the end of the pipe that is connected to the draft diverter. This suction carries away the exhaust from your furnace. The vent pipe is connected to the draft diverter (see B) which is mounted onto the furnace during installation. Refer to the Installer and Serviceman's Manual fo...
Otros modelos de este manual:Eléctrico - 5088-3 (162.09 kb)
Eléctrico - 3588-3 (162.09 kb)