Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Check that the appliance is suitable for the gas supply; refer to data labels on packaging and/or the fire for gas type. Note: Natural gas and Propane (LPG) models are not interchangeable. The gas installation must be in accordance with the current issue of BS6891.Gas supply pressure at the fire should be 20mbar for natural gas. The gas supply should be connected with the 1/4"BSP nut and olive with 8mm tubing. A maximum pipe run of 1.5 meters (or 5 feet) should be adhered to and copper tubing may be used provided a distance of 25mm is maintained between pipe-work and any surface of the fire. A gas service cock should be fitted adjacent to the fireplace to enable safe removal of the appliance for servicing. After fitting the supply, operate the gas cock (supplied) and check all joints up to the termination of the supply pipe for gas tightness using a soap/water solution and the pressure drop method. To check the pressure to the burner it is necessary to ignite the appliance and set to 'high rate'. This is carried out by following instructions on pages 9 and 10. Cold setting pressures are in the Technical data section on page 6. The pressure test point is located through the hole in the valve bracket marked 'test point', See Fig.8 below. Pressure test point Fig. 8 TEST SEQUENCE ENSURE FIRE IS OFF 1. Open control door. 2. Loosen test point screw. 3. Connect hose of test equipment to test point through the test point hole in bracket. (If necessary open fire door and remove coal set, base matrix plate and heatsheild. Close door on completion) 4. Turn on fire and set flame on high. 5. Take reading. 6. Turn fire off. 7. Remove test equipment hose. 8. Re-tighten test screw (If necessary replace heatsheild, matrix plate and coal set. Becton Bunny & Becton 7 mk3 Gas stoves INSTALLATION FIRE TESTING Flame failure device testing Step 1 Ignite the appliance in accordance with page 9 and run for 60 seconds. Step 2 Turn the appliance off to extinguish the pilot, listen for a snap at the control valve. This should occur within 60 seconds of the pilot flame being extinguished. The snap sound will be the magnet disengaging, and thus shutting off the flow of gas to the pilot and burner. Spillage Test A qualified gas engineer should Perform a spillage test as follows: Step 1. Close all doors and windows. Step 2 Light the appliance and set to the high rate. Step 3. Allow fire to warm up for 10 minutes. Step 4. Position the smoke match at the back of the fire centrally beneath the draught diverter as shown in Fig 9. All of the smoke should be drawn into the fire. If this does not occur the appliance must be disconnected and the flue checked. Step 5. If there is an extractor fan in any room, this must be turned on and any doors between it and the fire left open, repeat the spillage test. Repeated operation of the spillage monitoring system indicates that there maybe a flue draw problem. In this situation no more attempts at operating the appliance should take place and your gas engineer should be contacted. Warning: The spillage monitoring system is a safety feature required by law and must not be adjusted or put out of action by the installer. If the spillage monitoring system or any of its parts are to be replaced, only original manufacturers parts are to be used. Fig. 9 Note: The fire will give off non-toxic fumes when first used. This is perfectly normal and is due to the paint curing, it will disappear after the first few hours. Once the spillage test is complete open windows and doors to ventilate the area. Becton Bunny & Becton 7 mk3 Gas stoves INSTALLATION CHECK LIST CHECKLIST Hearths, Fireplaces, Flues and chimneys This checklist is to ensure hearths, fireplaces, flues and chimneys are satisfactory, and to show what you have done to comply with the requirements of The Building Regulations 2000 Approved Document J 2002. 1. Building address, where work has been carried out....................................................................................................................................... ......................................................................................................................................................................................................................... 2. Identification of hearth, fireplace chimney or flue 3. Firing capability: solid fuel/gas/. 4. Intended type of appliance. State model and output. 5. Ventilation provisions for the appliance: State type and area of permanently open vents. 6. Chimney or flue construction a) State the type or make and whether new or existing. b) internal flue size (and equivilent height, where calculated - natural draught gas appliances only). c) If clay or concrete flue liners used confirm that they are correctly jointed with socket end uppermost and state jointing materials used. d) If an existing chimney has been refurbished with a new liner, type or make of liner fitted. e) Details of flue outlet terminal and diagram ref...
Otros modelos de este manual:chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)