Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Outlet Details: Complies with: f) Number and angle of bends. g) Provision for cleaning and recommended frequency. 7. Hearth. Form of construction. New or existing? 8. Inspection and testing after completion Tests carried out by: Tests and results Flue visual inspection sweeping coring ball smoke Appliance (where included) spillage I/we the undersigned confirm that the above details are correct. In my opinion, these works comply with the relevant requirements in Part J of Schedule 1 to the Building regulations. Print name and title....................................................................................................Profession.......................................................................... Capacity......................................................................................................................Telephone.......................................................................... Address............................................................................................................................................................Postcode....................................... Signed........................................................................................................Date................................. Registered membership of..(e.g. CORGI, OFTEC, HETAS, NACE, NACS)............................................ Becton Bunny & Becton 7 mk3 Gas stoves SERVICING DETAIL OF PILOT ASSEMBLY It is strongly recommended to leave the pilot on permanently. This will keep the fire and its components, including the ceramic coal set in a warmer state and assist ignition to the burner. This in turn will reduce condensation in the chimney and any associated flue problems. The pilot can be viewed through the L/H & centre front slots in the base matrix. Fig. 10 Becton Bunny & Becton 7 mk3 Gas stoves SERVICING DOOR TRIM Becton Fire doors are fitted with a brushed steel finish trim as standard. The trim is secured using 3 off tabs and located in the slot section of the trim and secured with 3 off nuts. (See Fig. 11a below.) Note! fit a tracery the trim must first be removed. The fire door can only be fitted with one item at a time. REPLACEMENT THE DOOR TRIM Ensure the appliance is cold. Step 1 This is carried out by opening the door (secured with a magnet) and lifting it of (See Fig. 1 Fig 1 off its hinges Step 2 Place the door on a flat surface and remove the single tab. The tracery can now be removed. Step 3 The trim will now lift off the remaining 2 tabs. See Fig. 11d. Fig 11d Step 4 Repeat the above steps in reverse to replace the trim. FIRE DOOR GLASS & SEAL If necessary the glass and seal can be removed as follows: Ensure the appliance is cold. Step 1 Open the fire door. Step 2 The glass frame is secured using M5 screws. Remove all but the bottom 2 screws. See Fig. 12 below. Fig. 12 Removing the Glass Frame Step 3 Loosen the two remaining screws to enable you to lift off the glass frame and the glass and gasket assembly together. To re-fit the glass & seal. First ensure sealing faces are clean and free from dust. Then follow the removal steps in reverse. Note! The screws must be firmly secured to reform the seal. Fig. 11c Untightening the single tab Becton Bunny & Becton 7 mk3 Gas stoves SERVICING BURNER ASSEMBLY To remove the burner assembly proceed as follows; Ensure the appliance is cold. Step 1 Turn off the gas supply at the gas service cock. Step 2 Disconnect the supply inlet pipe at the rear of the fire. Step 3 Open door and remove the glass frame and glass gasket assembly. Step 4 Remove the coal set and fire box linings. Step 5 Remove the matrix location plate. Undo the three retaining nuts and lift out. Step 6 Remove the heat shield. Undo the two retaining nuts located on the left hand side of the shield. Slide the shield backwards and lift out carefully. Do not damage the covering. Step 7 Remove the gas valve control knob. Pull off. Step 8 Remove the 15mm retaining flange nut. 17mm socket. Step 9 Remove two off posi-drive screws just inside the fire door aperture. The burner assembly will now lift out. After replacement of burner assembly, ensure that a check on the gas tightness of any new joint is carried out. REGULAR SERVICE See "SAFETY NOTICES" ref coal set page 4. Any soot debris should be removed from the fuel bed regularly by the end user. Ensure the appliance is cold. Step 1 Isolate the gas supply from the fire. Step 2 Open the fire door and remove the glass frame and the glass/gasket assembly (Note the fire door is secured with a magnet). Step 3 Carefully remove and clean the coal set of any soot deposits with a soft a brush. Step 4 Remove any soot deposits from inside the fire using a vacuum cleaner. (See “Safety Notices” under ‘Coal set’ on page 4). Step 5 Replace the coal set. See assembly procedure on page Step 6 Replace glass/gasket assembly and glass frame. Step 7 Close fire door. Becton Bunny & Becton 7 mk3 Gas stoves SERVICING ANNU...
Otros modelos de este manual:chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)
chimeneas - Becton 7 mk3 (524.86 kb)