Slide heater down until screws are in small portion of slots. Figure 9 - Location Of Keyhole Slots On Back Panel Of Heater Keyhole Slots Removing Front Panel Of Heater 1. Remove two screws near bottom corners of front panel. 2. Lift straight up on grill guard until it stops. Grill guard will slide up about 1/4". 3. Pull bottom of front panel forward, then down. Figure 10 - Removing Front Panel Of Heater Installing Bottom Mounting Screw 1. Locate bottom mounting hole. This hole is near bottom on

Inlet Gas Pressure (inches of water) Maximum 10.5" Minimum 4" Dimensions, Inches (H x W x D) Heater (Including knobs and grill) 21 1/2 x 13 1/2 x 7 Carton 25 1/4 x 16 3/4 x 7 1/2 Weight (pounds) Shipping 19 When gas pressure is too low • pilot will not stay lit • burner will have delayed ignition • heater will not produce specified heat When gas quality is bad • pilot will not stay lit • burner will produce flames and soot • heater will backfire when lit You may feel your gas pressure is too low

injury or property damage. Re m Do not store or use gasoline or other flammable fer to this manual for correct vapors and liquids in the vicinity of this or any other installation and operational pro- appliance. cedures. For assistance or addi- WHAT TO DO IF YOU SMELL GAS tional information consult a qualified installer, service agency, or • Do not try to light any appliance. the gas supplier. • Do not touch any electrical switch; do not use any phone in your building. WARNING: For use only with

Continued UNVENTED (VENT-FREE) FIREBOX INSTALLATION Continued INSTALLING BLOWER ACCESSORY (MODEL CGFB32C ONLY) You may install blower accessory GA3750 with conventional installation (below) or with built-in installation (page 10) with model CGFB32C only. To install blower accessory, see instruction sheet included with the kit. Conventional Installation of Blower Accessory 1. Install blower assembly per instruction sheet included in blower accessory kit. 2. Before replacing bottom of firebox, rou

Burner orifice clogged 2. Inlet gas pressure is too low 3. Thermopile leads disconnected or improperly connected 4. Burners will not come on in remote position 1. Clean burner (see Cleaning and Maintenance, pages 16 and 17) or replace burner orifice 2. Contact local gas company 3. Reconnect leads (see wiring diagram) 4. Replace battery in transmitter and receiver Delayed ignition burner 1. Manifold pressure is too low 2. Burner orifice clogged 1. Contact local gas company 2. Clean burner (see Cl

7. Attach the two mounting brackets to blower housing using four screws provided in blower kit (2 for each bracket) (see Figure 16, page 13). Tighten screws securely. Place blower assembly temporarily on top of firebox. 8. Working from the rear of the stove, place entire power cord, including speed control housing, in lower control compartment. 9. Route ends of 3-wire power cord up from the lower control compartment through the plastic bushing, then up to the upper cavity of stove (see Figure 17

3. You prefer vented operation. If reasons number 1 or 2 above apply to you, you must permanently open chimney flue damper. You must install the damper clamp accessory (to order, see Accessories, page 33). This will insure vented operation (see Figure 10). The damper clamp will keep damper open. Installation instructions are included with clamp accessory. See chart below for minimum permanent flue opening you must provide. Attach damper clamp so the minimum permanent flue opening will be maintai

LA Porte’s Parts & 601 Hope Street P.O. Box 6129 Service Bowling Green, KY 42101 Freehold, NJ 07728 2444 N. 5th Street 502-796-8406 908-780-9340 Hartsville, SC 29550 1-800-654-8534 1-800-922-0724 803-332-0191 Parts Department Four Flags Power Products Albany Ladder 1115 Stateline Road 1586-90 Central Avenue Cans Unlimited, Inc. Niles, MI 49120 Albany, NY 12205 P.O. Box 645 616-684-2697 NY, MA, VT Taylor, SC 29687 Parts Only 518-869-5335 All States 1-800-354-7368 803-879-3009 Master Service Cente

With sheet metal, you must have non combustible material behind it. Non combustible material must extend at least 8" up (for all models). If non combustible material is less than 12", you must install the fireplace hood accessory (24" and 30" models only). See chart below and Figure 5 for minimum clearances. IMPORTANT:If you cannot meet these minimum clearances, you must operate heater with chimney flue damper open. Go to Installing Damper Clamp Accessory for Vented Operation, page 13. Heat Resi

Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 21). Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" or greater diameter to allow proper gas volume to heater. If pipe is too