Votos - 1, Puntuación media: 4 ( )

Fabricar: Bloomfield Tamaño del archivo: 1.63 mb Nombre del archivo: Idioma del manual:

Press the ON/OFF key again to turn the brewer OFF. Three beeps will sound, the tank heater and all warmers will be switched off, and all indicator lights will go out. Brew Settings See pages 17 & 18 for setting Brew Time and Temperature. ABS™ (Automatic Brew Start) Start a brew by pressing BREW. A single beep will sound. The system will verify that the water in the tank is at the proper temperature. If it is, brew will start immediately. Otherwise, the BREW indicator will flash (Brew Waiting Mode) until the water reaches setpoint temperature, then the indicator will glow and brew will commence. If the main warmer is off, it will be energized automatically. At the conclusion of the brew cycle, three beeps will sound. NOTE: To override Brew Waiting Mode, press and hold the BREW key for 3 seconds while the BREW indicator is flashing. Brew will begin regardless of water temperature. To avoid under-temperature brews, this feature should only be used when setting brew volumes. NOTE: Brew Waiting Mode (BREW indicator flashing) prevents multiple, unattended brews. While the BREW indicator is on or flashing, any additional strokes of the BREW key will be ignored (there will be a beep each time the key is pressed, however). Another brew cannot be initiated until the previous brew is complete. The Brew Waiting Time, also called Dripout Time, (interval between when the brew is initiated and the audible signal sounds at the end of the brew) may be adjusted between 2 and 8 minutes at the Brew Signal Timer dial on the controller. See page 18. Brew Cancel To cancel a brew in progress or a brew in waiting, press the CANCEL key. Two beeps will sound and the BREW indicator will go out. NOTE: If a brew in progress is cancelled, coffee will continue to flow until all water delivered has dripped through the brew chamber. IMPORTANT: DO NOT energize this brewer until the water tank has been filled. Dry firing will damage heating elements. See page 6. Fig. 7 Turning Brewer ON or OFF Fig. 8 Initiate a Brew Fig 9 Brew Cancel 8 OPERATION (continued) ELECTRONIC FEATURES Energizing the Brewer When electric power is applied to the unit, all the lights will flash four times and four beeps will sound. The unit will be OFF. Press the ON/OFF key. Four beeps will sound and all lights will flash once. The POWER indicator will remain ON. If the water temperature is more than 10.F below the setpoint, the HEAT indicator will glow until water temperature reaches setpoint. Press the ON/OFF key again to turn the brewer OFF. Three beeps will sound, the tank heater and all warmers will be switched off, and all indicator lights will go out. Brew Settings See pages 17 & 18 for setting Brew Time and Temperature. ABS™ (Automatic Brew Start) Start a brew by pressing BREW. A single beep will sound. The system will verify that the water in the tank is at the proper temperature. If it is, brew will start immediately. Otherwise, the BREW indicator will flash (Brew Waiting Mode) until the water reaches setpoint temperature, then the indicator will glow and brew will commence. If the main warmer is off, it will be energized automatically. At the conclusion of the brew cycle, three beeps will sound. NOTE: To override Brew Waiting Mode, press and hold the BREW key for 3 seconds while the BREW indicator is flashing. Brew will begin regardless of water temperature. To avoid under-temperature brews, this feature should only be used when setting brew volumes. NOTE: Brew Waiting Mode (BREW indicator flashing) prevents multiple, unattended brews. While the BREW indicator is on or flashing, any additional strokes of the BREW key will be ignored (there will be a beep each time the key is pressed, however). Another brew cannot be initiated until the previous brew is complete. The Brew Waiting Time, also called Dripout Time, (interval between when the brew is initiated and the audible signal sounds at the end of the brew) may be adjusted between 2 and 8 minutes at the Brew Signal Timer dial on the controller. See page 18. Brew Cancel To cancel a brew in progress or a brew in waiting, press the CANCEL key. Two beeps will sound and the BREW indicator will go out. NOTE: If a brew in progress is cancelled, coffee will continue to flow until all water delivered has dripped through the brew chamber. IMPORTANT: DO NOT energize this brewer until the water tank has been filled. Dry firing will damage heating elements. See page 6. Fig. 7 Turning Brewer ON or OFF Fig. 8 Initiate a Brew Fig 9 Brew Cancel OPERATION (continued) OPERATION (continued) 641 75844 Owners Manual E. B.C. Decanter Quality Timer Coffee looses its freshness as it sits on a warmer. The Quality Timer flashes the warmer lights 30 minutes after the last brew to remind you that the coffee is nearing the end of its useful life. After Hours™ Operation During normal operation, the controller will maintain the precise brewing temperature. If, however, if the BREW key in not pressed for 3 hours, the brewer goes into After H...

Descargar ahora

Introduzca dos números de la imagen: