Votos - , Puntuación media:
(
)
)
Fabricar: Salton
Tamaño del archivo: 119.95 kb
Nombre del archivo: c8e96744-0e2f-462e-a292-9e2dcaf2d39e.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
When you have prepared the filter and placed it into the Holder on the Water Tank Lid, you may add water. Again, follow the filter manufacturer’s directions. Make sure that water has actually flowed into the tank before you start brewing. Filter flow rates vary from brand to brand, so always check first. Brewing Espresso 1. Plug the machine into a 120V ~ 60 Hz outlet. 2. Before brewing espresso, make sure the Water Tank is filled with fresh water. 3. Replace the Water Tank to its original position, making sure it is properly seated on the machine. 4. Close the Lid on the top of the Water Tank. 5. Place a heat resistant cup under the Coffee Spout, on top of the Cup Rest Grill. 6. Switch the machine to the “ON” position to heat and press the “COFFEE CUP”.Temperature Switch to the 7 Brewing Espresso (continued) Function Selector NEUTRAL position Function Selector COFFEE position IMPORTANT! You can brew espresso shots one after another. Always wait for the Green “GO” Light. That’s the signal to brew. 11. When brewing is completed, the Coffee Pod will fall into the Used Pod Container and 123 Spresso will automatically set up to brew the next coffee. • NOTE: If you prefer a strong, robust cup of coffee, brew one ounce shots. If you prefer milder coffee, use more water to suit your taste. Let the coffee brew for approximately 10 - 15 seconds. 10. Turn the Function Selector to the “NEUTRAL” Position. 7. When the Green “GO” Light illuminates, flip the Function Selector (on the side of the machine) to “COFFEE CUP”. MAKE SURE THE GREEN “GO” LIGHT IS ILLUMINATED BEFORE PLACING COFFEE POD INTO THE MACHINE. Brewing Espresso (continued) Function Selector NEUTRAL position Function Selector COFFEE position IMPORTANT! You can brew espresso shots one after another. Always wait for the Green “GO” Light. That’s the signal to brew. 11. When brewing is completed, the Coffee Pod will fall into the Used Pod Container and 123 Spresso will automatically set up to brew the next coffee. • NOTE: If you prefer a strong, robust cup of coffee, brew one ounce shots. If you prefer milder coffee, use more water to suit your taste. Let the coffee brew for approximately 10 - 15 seconds. 10. Turn the Function Selector to the “NEUTRAL” Position. 7. When the Green “GO” Light illuminates, flip the Function Selector (on the side of the machine) to “COFFEE CUP”. MAKE SURE THE GREEN “GO” LIGHT IS ILLUMINATED BEFORE PLACING COFFEE POD INTO THE MACHINE. CAUTION: YOU MUST STOP THE WATER FLOW BY TURNING THE FUNCTION SELECTOR TO “NEUTRAL.” THE • WATER FLOW DOES NOT STOP AUTOMATICALLY. 8 Prepare Cappuccinos, Lattes, Mochas, Macchiatos and More! The steam function can be used to make hot milk for cafe latte or to make froth for cappuccino. 1. Place your cup of espresso on the 123 Spresso handy Cup Warmer. This will help keep the coffee warm. 2. Press the ON/OFF Switch to the “ON” position. 3. To prepare steam for froth, turn the Temperature Switch to the “STEAM/FROTH” Position. 4. Slide Frothing Attachment onto Steam Nozzle as far as possible. The Frothing Attachment fits snugly over the Steam Nozzle. Always turn small pressure relief hole so that it is pointed backwards, facing the machine. Swivel the frothing tube outward, away from the machine and towards you. Adjust the Frothing Attachment so that it fits down into a heat proof cup or handled frothing pitcher with cold milk. 5. Fill the frothing pitcher 1/3 to 1/2 full with cold milk. 6. When the machine has heated to the correct temperature and is ready to froth milk, the Green “GO” Light will illuminate. Function Selector STEAM/FROTH position 7. Turn the Function Selector from “NEUTRAL” to the “STEAM/ • FROTH” Position. 8. The machine will automatically begin to release steam. 9 Cappuccino/Coffee Drinks (continued) Cappuccino/Coffee Drinks (continued) . When making froth for cappuccino, hold the Frothing Attachment below the surface of the cold milk. Do not touch the bottom of the pitcher with the Frothing Attachment. While frothing, move the pitcher in a circular motion then up and down for best results. This allows the steam to mix with air to create rich, creamy froth. Foam should be dense with small, closely packed bubbles for rich taste and long-lasting foam. 10. Wipe the Frothing Attachment with a clean, damp cloth. 11. To complete your cup of cappuccino, take the cup of espresso from the Cup Warmer, pour 1 ounce of steamed milk into espresso and spoon the froth on top of the coffee. For the final touch, sprinkle cinnamon, nutmeg, chocolate shavings, cocoa powder, etc. on top of the froth. See Espresso Terms and Expresso Recipes in the back of this manual. 10 Care and Cleaning Instructions Care and Cleaning Instructions Hint: When the Overflow Tray is full, the red flag will pop up to alert you it needs to be emptied. Make sure the machine is fully cooled. Simply pull tray straight out and pour out into your sink until it is empty. Clean and slide back into machine securely. Used Pod Container DI...
Otros modelos de este manual:Cafeteras - MEPE123W (119.95 kb)