1. Install the mezzanine card as shown below.
European Union regulatory
Mezzanine Card
Overview
notice
Installation Instructions
Use these instructions to install optional mezzanine cards.
This product complies with the following EU Directives:
Optional mezzanine cards are classified as Type I mezzanine
•
Low Voltage Directive 2006/95/EC
for supported HP BladeSystem c-Class server blades
cards and Type II mezzanine cards. The type of the
•
mezzanine card determines where it can be installed in the

EMC Directive 2004/108/EC

server blade.
Compliance with these directives implies conformity to



applicable harmonized European standards (European

Install Type I mezzanine cards on Mezzanine 1 connector,
Norms) which are listed on the EU Declaration of Conformity
Mezzanine 2 connector, or Mezzanine 3 connector.

issued by Hewlett-Packard for this product or product family.
Install Type II mezzanine cards on either Mezzanine 2
This compliance is indicated by the following conformity
connector or Mezzanine 3 connector.
marking placed on the product:

Warnings and cautions

Or, for half-height server blades install as shown.


This marking is valid for non-Telecom products and EU
WARNING: To reduce the risk of personal injury
harmonized Telecom products (e.g. Bluetooth).
from hot surfaces, allow the drives and the internal

system components to cool before touching them.




WARNING: Reduce the risk of electric shock by
removing all AC power from the system before

installing or replacing any non-hot-plug hardware
This marking is valid for EU non-harmonized Telecom
option. Disconnect all power cords to completely
products.
remove power from the server.

*Notified body number (used only if applicable—refer to the

CAUTION: Electrostatic discharge (ESD) can
product label)
damage electronic components. Be sure that you are
Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140,
properly grounded (earthed) before beginning any
71034 Boeblingen, Germany
installation procedure.



2. Reinstall the access panel.


Korean class A notice
CAUTION: Limit the number of times that a
NOTE: See the HP BladeSystem Enclosure Setup and
mezzanine card is installed and removed within its
Installation Guide for more information on the
lifecycle to prevent connector pin damage.
association between the mezzanine bay and the


interconnect bays. Where you install the mezzanine
Removing the access panel
card will determine where you need to install the
interconnect modules.

1. Identify the proper server blade in the enclosure.
3. Restore the server blade to its operating position in the

2. Back up all server blade data.
server blade enclosure.

3. Power down the server blade.
NOTE: By default, the server blade will power up on
4. Remove the server blade.
installation.


5. Lift the access panel latch and slide the access panel to
© Copyright 2006 - 2007 Hewlett-Packard Development Company, L.P.
the rear.
The information contained herein is subject to change without notice. The
Completing the installation
only warranties for HP products and services are set forth in the express
6. Remove the access panel.

warranty statements accompanying such products and services. Nothing
For information about installing and configuring drivers for
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Installing the mezzanine card
your specific operating system and mezzanine card refer to
the HP website


(http://www.hp.com/go/bladesystem/mezzanines).
April 2007 (Second Edition)
IMPORTANT: Remove the mezzanine card

Part Number 413773-022
connector protective cover, if installed.
413773- 022


Printed in the US

---

...

Otros modelos de este manual:
Computadoras - HP ProLiant xw460c Blade Workstation (735.47 kb)
Computadoras - HP ProLiant BL480c Server Blade (735.47 kb)