Votos - 0, Puntuación media: 0
(
)
)
|
Otros manuales para este modelo:
Computadoras - HP xw8200 Workstation (1.46 mb)
Computadoras - HP xw8200 Workstation (460.6 kb)
Computadoras - HP xw8200 Workstation (1.13 mb)
Resumen del manual
SATA/SAS Hard Drive Installation
Important Warnings and Cautions
6. If installing a SAS hard drive, attach the SAS-to-SATA cable
Creating a Partition Using Microsoft Windows XP
Guide
adapter. The cable adapter is provided with the kit and is
not required when installing SATA hard drives.
1. Log in as Administrator.
WARNING! To avoid the risk of serious injury or damage
2. From the Windows desktop, click Start > Control Panel.
to the computer, unplug the power cord from the electrical
3. Double-click Administrative Tools.
outlet before installing the hard drive.
4. Double-click Computer Management.
5. Select Storage > Disk Management. This starts the Write
WARNING! To reduce the risk of personal injury from hot
Signature and Upgrade Disk Wizard. Click Cancel to stop
surfaces, allow the internal system to cool before touching
the wizard.
it.
NOTE: You may be prompted by the system to upgrade to
a Dynamic drive. Refer to www.microsoft.com/support for
CAUTION: Static electricity can damage the electronic
more information or refer to the Microsoft OS Manual that
components of the computer or optional equipment. Before
shipped with the computer. Otherwise, select the default to
installing the hard drive, ensure that you are static-free by
continue.
briefly touching a grounded metal object. Refer to the
documentation that came with the computer for more
6. Right-click the Disk 1 Unallocated area.
information on preventing electrostatic damage.
7. Connect the power cable 1 and data cable 2 to the hard
7. Click Initialize Disk and click OK.
drive.
8. Right-click the black bar above the Unallocated Disk area.
9. Click New Partition to run the New Partition Wizard. Click
© Copyright 2006 Hewlett-Packard Development Company, L.P. The
CAUTION: Prior to replacing an existing hard drive, be
Next.
information contained herein is subject to change without notice.The only
sure to back up your data. If the computer supports only
10. Select the partition needed or use the defaults and click
warranties for HP products and services are set forth in the express warranty
one hard drive, you must use a second system with third-
Next.
statements accompanying such products and services. Nothing herein should
be construed as constituting an additional warranty. HP shall not be liable for
party software to copy the data to the new hard drive.
11. Specify the partition size or use the defaults and click Next.
technical or editorial errors or omissions contained herein.
12. Specify the drive letter of the partition or use the default
and click Next.
CAUTION: The data cable end is keyed to ensure proper
First Edition: May 2006
alignment. To avoid damage to the cable header pins,
13. Select Choose Partition File System and other Partition
Parameters or use the defaults and click Next.
check the header/connector alignment and push gently
14. Verify that the information in the Set ings box is correct
Your Responsibilities
when connecting the data cable header to the SATA
before finalizing the partition information.
connector on the drive and system board.
15. Click Finish to create the partition and begin the format
You are responsible for determining whether the product is
process.
appropriate for your use and will function with other equipment
without malfunction or damage. You are also responsible for
Installing the Hard Drive
8. Connect the opposite end of the data cable to the system
backing up data before installing any product and for regularly
board or controller card.
backing up data after installing the product. HP is not liable for
any damage to equipment or data loss resulting from the use of
NOTE: For specific information relating to your HP xw
CAUTION: To avoid any hard drive performance
any product.
Series Workstation, refer to www.hp.com/go/bizsupport.
problems, connect the primary hard drive to the connector
on the system board labeled SATA 0 or SAS 0, depending
Regulatory Notices
1. Turn off the computer and any external devices.
on hard drive type. Connect a second hard drive to the
2. Disconnect the AC power cord and any external devices.
SATA 1 or SAS 1 connector. Connect a third hard drive to
This product has been tested and found to comply with the limits
3. Remove the side access panel from the computer.
the SATA 2 or SAS 2 connector and a fourth hard drive to
for a Class B digital device of the FCC Rules. Refer to the
4. Install the hard drive into the drive bay.
the SATA 3 or SAS 4 connector.
documentation that came with the computer for additional
5. Identify the cable that best fits your SATA or SAS hard drive
regulatory information governing this product.
by referring to the Cable Identification Table.
9. Replace the side access panel.
10. Reconnect any external devices to the computer.
Technical Support
11. Plug the AC power cord into the computer, then into a
grounded AC outlet.
xw4000 series
3.5” internal drive bays (2)
381868-006
Comprehensive technical support is available online at
http://www.hp.com/support.
3.5” external drive bay (1)
not allowed
Configuring the Computer
You can also call HP for technical support. Refer to the
5.25” external drive bays (3)1
381868-002
documentation that came with the computer for support
System configuration is the process of specifying the devices and
telephone numbers.
xw6000 series
3.5” internal drive bays (2)
381868-006
programs that make up a computer system. When you add or
remove accessories, the computer must be configured to
3.5” external drive bay (1)
not allowed
recognize these changes.
5.25 external “upper” bay (1)
not allowed
Turn on the computer and read the messages displayed during
5.25” external “lower” bay (1)1
381868-002
startup.
xw8000 and
3.5” internal drive bays (4)
381868-006
• If the system recognizes the new drive, information about
xw9000 series
the drive displays on the screen, and you are prompted to
3.5” internal chassis mount bay (1) 381868-002
press F1 to save and continue.
5.25” external bays (3)
not allowed
• If you are not prompted to press F1, there is a problem with
1. Hard drives installed in 5.25” external bays require a hard drive conversion
the installation of the drive, and you need to diagnose the
bracket, which is available by finding your workstation at www.hp.com and
problem. Start by reviewing the steps in this guide.
selecting Options and Accessories.
...