Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The options are: 3 (Default), 1. Serial Port 1/2/3/4 IRQ The IRQ of serial port 1/2/3/4 can share the same one or not. The options are: 4/3/10/5(default), 4/3/3/3, 4/3/10/10, 4/3/4/3, share 3, share 3, share 4, share 5, share 10 (share IRQ is reserved). Vector Hi/Low select (Reserved) You can select the interrupt vector level. The options are: low (default), high Vector Address Decoder (Reserved) You can choose the interrupt vector address, the default is 200. 9.11 Password Setting To enable the password setting, select the item from the Standard CMOS Setup. You will be prompted to create your own password. Type your password up to eight characters and press "Enter". You will be asked to confirm the password. Type the password again and press "Enter". You may also press "Esc" to abort the selection and not enter a password. To disable the password, press "Enter" when you are prompted to enter the password. A message will appear, confirming the password is disabled. Under the BIOS Features setup, if "System" is selected under the Security Option field and the Supervisor Password is enabled, you will be prompted for the supervisor password every time you try to enter the 122 IPPC-9120/9150 Series User's Manual CMOS Setup utility. If "System" is selected and User Password is enabled, you will be requested to enter the user password every time you reboot the system. If "Setup" is selected under the Security Option field and User Password is enabled, you will be prompted only when you reboot the system. 9.12 IDE HDD Auto Detection Figure 9-9: IDE HDD auto detection screen The IDE Hard Disk Drive Auto Detection feature automatically configures your new hard disk. Use it for quick configuration of new hard disk drives. This feature allows you to set the parameters of up to four IDE HDDs. The option with "(Y)" is recommended by the system BIOS. You may also key in your own parameters instead of setting them according to the system BIOS. After keying in all settings, press "Esc" to return to the main menu. For confirmation, enter the Standard CMOS Setup feature. Chapter 9 Award BIOS Setup 123 9.13 Save and Exit Setup Figure 9-10: Save and exit setup screen After you have made changes in the BIOS setup, press "Esc" to return to the main menu. Move the cursor to "Save and Exit Setup", or press "F10" and then press "Y", to change the CMOS Setup. If you did not change anything, press "Esc" again or move the cursor to "Exit Without Saving" and press "Y" to retain the setup settings. The following message will appear at the center of the screen to allow you to save data to CMOS and exit the setup utility: SAVE to CMOS and EXIT (Y/N)? 9.14 Exit Without Saving If you select this feature, the following message will appear at the center of the screen to allow you to exit the setup utility without saving CMOS modifications: Quit Without Saving (Y/N) ? 124 IPPC-9120/9150 Series User's Manual A LCD Specifications and Selection Settings APPENDIX Table A-1: IPPC-9120/9150 Series LCD specifications Model IPPC-9120T IPPC-9150T Display type (LCD) 12.1" TFT LCD 15" TFT LCD Max. resolution 800 x 600 1024 x 768 Colors 256 K colors 256 K colors Dot pitch (mm) 0.31 x 0.31 0.29 x 0.29 Viewing angle 100°(H),120°(V) 100°(H),120°(V) Luminance 250 cd/sq meter 250 cd/sq meter Viewing area 246 x 184.5 mm 304 x 228 mm Power consumption +5 V @ 1 A max. +5 V @ 1 A max. Operating temperature 0° ~ 50° C 0° ~ 50° C Storage temperature -20° ~ 60° C -20° ~ 60° C LCD MTBF 50,000 hours 50,000 hours Backlight MTBF 25,000 hours 25,000 hours Note: The color LCD display installed in the IPPC-9120/9150 Series is high-quality and reliable. However, it may contain a few defective pixels which may not always illuminate.With current technology, it is impossible to completely eliminate defective pixels. Advantech is actively working to improve this technology. 126 IPPC-9120/9150 Series User's Manual B Programming the Watchdog Timer The IPPC-9120/9150 is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments. APPENDIX B.1 Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a time interval value. The value range is from 01 (hex) to 3E (hex), and the related time interval is from 1 sec. to 62 sec. Data Time Interval 01 1 sec. 02 2 sec. 03 3 sec. 04 4 sec. 3E 62 sec. After data entry, your program must refresh the watchdog timer by rewriting the I/O port 443 (hex) while simultaneously setting it. When you want to disable the watchdog timer, your program should read I/O port 443 (hex). 128 IPPC-9120/9150 Series User's Manual The following example shows how you might program the watchdog timer in BASIC: 10 REM Watchdog timer example program 20 OUT &H443, data REM Start and restart the watchdog 30 GOSUB 1000 REM Your ...
Otros modelos de este manual:Computadoras - RUGGED PENTIUM IPPC-9150 (5.24 mb)