Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
See “To Operate on Fan Only” section on Page 6. TO CHANGE TEMPERATURE SETTING: PRESS TO RAISE PRESS TO LOWER DO THIS: AUTO TEMP SETS DISPLAYS TEMPERATURE/TIME FAN SPEED ACTIVATES TIMER CHECK FILTER RESET BUTTON SETS MODE TURNS UNIT ON OR OFF AUTO TEMP FEATURE SLEEP MODE SETS FAN SPEED ADJUSTS TEMP & TIME 6 Air Conditioner Features (continued) TO ADJUST FAN SPEEDS: YOU WILL SEE : DO THIS: PRESS TO SELECT: FASTER SLOWER TO USE AUTO TEMP FEATURE: YOU WILL SEE: Note: Fan speed starts at High Speed and adjusts to a slower speed as the room temperature dictates. For example if the room doesn’t get too warm, it will stay at the slowest speed. If the room temperature rises quickly, such as a door being opened, it will automatically go to the highest speed. The fan speeds will re-adjust back to the slowest speed as the room returns to the original set temperature. DO THIS: PRESS AUTO TEMP BUTTON LIGHT ON TO OPERATE ON FAN ONLY: YOU WILL SEE: Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Except “Auto Temp”). During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode. LIGHT ON DO THIS: PRESS MODE BUTTON CHOOSE FAN ONLY Press the Fan Faster button will increase the fan speed from Low (LO), to Medium (ME), to High (HI). The digital display will indicate your chosen speed. Press the Fan Slower button will decrease the fan speed from High (HI), to Medium (ME), to Low (LO).The digital display will indicate your chosen speed.After 5 seconds the display will revert back to the set temperature. Fan Only cannot be selected when the unit is in the 'Remote Sensing' Mode. (On those units with that feature). 7 Air Conditioner Features (continued) YOU WILL SEE: Note: In this mode, the fan will continue to run for another 3 minutes after the compressor shuts off. The fan then cycles on for 2 minutes at 10 minute intervals until the room temperature is above the set temperature, at which time the the cooling system turns back on. TIME IS CHOSEN: Note 1: For Delay Stop, the unit must be in the On position. Note 2: For Delay Start, the unit must be in the Off position. First, PRESS TIME BUTTON LIGHT ON TO USE THE ENERGY SAVER FEATURE: LIGHT ON DO THIS: PRESS MODE BUTTON CHOOSE ENERGY SAVER TIMER: DELAY STOP / START FEATURE: YOU WILL SEE HOW MUCH FIRST DO THIS: PRESS TIMER BUTTON THEN DO THIS: PRESS TEMP/TIMER SET BUTTON Then to adjust timer setting, tap or hold the UP arrow ( ) or the DOWN arrow ( ) to change delay timer at .5 hour increments, up to 10 hours, then by 1 hour increments up to 24 hours. The control will count down the time remaining until start (8, 7.5, 7, etc.). The Delay Start mode automatically selects cooling with maximum Fan Speed. The temperature maintained will be the same as previously set. To change the set temperature, press “COOL” then Up or Down arrows until the desired temperature is indicated on the display. After 5 seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. PRESSING the unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either starts or stops. Once that happens he above steps have to be repeated again. 8 Air Conditioner Features (continued) CHECK FILTER FEATURE: Note: In this “MODE” the set temperature will increase by 2 degrees F 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. This ends the “Sleep” MODE and the unit will continue to operate as originally programmed. The “Sleep” MODE program can be cancelled at any time during operation by again pressing the “Sleep” button. DO THIS: PRESS SLEEP BUTTON LIGHT ON TO TURN UNIT OFF: YOU WILL SEE: DO THIS: PRESS ON/OFF BUTTON YOU WILL SEE : LIGHT ON Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Check Filter” button and the light will go off. SLEEP FEATURE: YOU WILL SEE: FAULT CODES: If the display reads"AS", a sensor has failed.Contact your Authorized Frigidaire Service Center. If the display reads"ES", a sensor has failed.Contact your Authorized Frigidaire Service Center. Air Conditioner Features (continued) ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedure, here are more features in your control that you should become familiar with. • The “Cool “ circuit has an automatic 3 minute time delayed start if the unit is turned off...
Otros modelos de este manual:Los acondicionadores de aire - 100BTU-25 (1.83 mb)
Los acondicionadores de aire - 15 (1.83 mb)