Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Wait a few seconds for the data to be acquired. • The indicator light (I) flashes until the appliance starts up. •You can set the appliance to come on with a delay of up to 24 hours. •To cancel the timer setting, press the timer button (H), and use the “-” (P) button to set the time to “00”. The indicator light (I) will stop flashing. How to program delayed shut down • Delayed shut down can be programmed in any operating mode. •Press the timer button (H). The two center segments flash on the display. • Use the “+” (G) or “-” (P) button to set the number of hours delay before the appliance goes off. The setting is increased or decreased by an hour at a time; however, when the buttons are held down for more than two seconds, the time runs rapidly up to a maximum of 24 hours. Wait a few seconds for the data to be acquired. • The indicator light (I) flashes until the appliance shuts down. •To cancel the timer setting, press the timer button (H), and use the “-” (P) button to set the time to zero. The indicator light (I) will stop flashing. The remote control The remote control Depending on the model, the temperature on the display is shown in °C or °F. However, the illu strations in the manual give the values in °F. THE REMOTE CONTROL Inserting/replacing batteries (included) • Remove the back cover (see figure). • Insert two new batteries (not rechargeable) making sure the (+) and (-) are in the correct positions. • Replace the back cover. Note: Alkaline batteries should be used (LR03 AAA type). Used batteries can be harmful to the environment, and should not be thrown out with household waste. Contact your local government to find out if they have a battery recycling program or how to dispose of used batteries. Warning: Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. Do not dispose of batteries in fire: batteries may explode or leak. If the remote control is not be used for a certain length of time, remove the batteries. CORRECT USE • Aim the remote control at the signal receiver on the air-conditioner. • Maximum distance: around 23 ft. (7 meters) (without obstacles between the remote control and the receiver). • The remote control should be handled with extreme care: without dropping it, without exposing it to direct sunlight or near sources of heat. 1 2 Description of the remote control Description of the remote control THE REMOTE CONTROL A. MODE button Selects the operating mode (air conditioair filtration, Buttons for SETTING THE ROOM TEMPERATU- Set room temperature or program the to automatic, high, ) Sets or cancels the automatic SLEEP func ) When this button is pressed, the appliance automatically establishes the most suitamode for maximum ) Press this button to turn the appliance on Note: the settings are displayed even when the air conditioner is in stand by. A E D C B B I H G BOOST Activates the motorized lowers.F SWING SPEED %RH ning, dehumidification, Smart). B. RE timer. C. SPEED button Sets fan speed medium or low in sequence. D. SWING button E. TIMER button Sets or cancels the timer. Starts or stops rapid cooling. In the rapid cooling mode, the fan operates at high speed with the temperature automatical- ly set to 64°F (18°C). button mode (see page 14 for further information) Remote control functions Remote control functions AIR-CONDITIONING MODE •Press the button (I) to turn the appliance on. • The symbol flashes on the display and a “beep” indicates that the air-conditioning unit is on. • Press the MODE button (A) a number of times until the air-conditioning symbol appears on the display. • Now set the temperature using the buttons. • To select fan speed, press the SPEED button (C) repeatedly until the required fan speed is selected (automatic, high, medium, low). NB: in air-conditioning mode, the appliance automatically removes excess moisture from the atmosphere. DEHUMIDIFYING • Activate this function when humidity is high. •Press the button (I) to turn the appliance on. The symbol flashes on the display and a “beep” indicates that the air conditioner unit is on. •Press the MODE button (A) a number of times until the dehumidifying symbol appears on the display. • Set the required humidity level using the buttons. • In dehumidifying mode, fan speed is selected by the appliance automatically. • Place the appliance in the room without fitting the air exhaust hose. FAN MODE WITH AIR FILTRATION In humid but not particularly hot days, the fan function alone may be adequate. •Press the button (I) to turn the appliance on. The symbol flashes on the display and a “beep” indicates that the air-conditioning unit is on. •Press the MODE button (A) a number of times until the fan symbol appears on the display. • Once purifying mode has been selected, press the SPEED button (C) until the required speed is reached (low, medium, high). BOOST FUNCTION “BOOST” function is used to obtain rapid cooling. The fan is set to high speed and the...
Otros modelos de este manual:Los acondicionadores de aire - PINGUINO PACT100P (823.28 kb)