Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Broan Tamaño del archivo: 104.5 kb Nombre del archivo: Idioma del manual:

4. Proporcione un circuito electrico de capacidad nominal al calentador, a fin de impedir la desconexion de disyuntores o quemado de fusibles. (Vease el diagrama abajo). 5. NO CONECTE EL CALENTADOR AL CONMUTADOR REDUCTOR O CONTROL DE VELOCIDAD. 6. Para evitar danos al cojinete del motor e impulsores ruidosos y/o desequilibrados, mantenga la unidad de energia alejada de rocios de yeso, polvo de construccion, etc. 7. Para mas informacion y requisitos, lea la etiqueta de especificacion sobre el producto. PLANIFICACION DE LA INSTALACION Este conjunto de acabado para calentador de pared ha sido disenado para instalacion en una caja Broan modelo 171H de etapa inicial de instalacion, despues de que se haya completado la pared. El calentador se puede poner en funcionamiento usando su termostato incorporado o un termostato a distancia (termostato de tension de linea Broan modelo 86 - adquieralo en forma separada). La tabla que aparece a continuacion enumera las corrientes nominales para cada modelo. El cableado viene de fabrica para las corrientes nominales GRILLE REJILLA POWER CABLE CABLE DE ENERGIA ELECTRICA DRYWALL PARED DE YESO WALL STUD ESPIGA DE PARED FIG. 1 BUILT-IN THERMOSTAT TERMOSTATO INCORPORADO HEATER HOUSING CAJA DEL CALENTADOR BOLD ratings are factory wired. See “OPTIONAL WIRING CONVERSIONS” section on page 3 for wattage and voltage conversion instructions. INSTALLATION This wall heater finish assembly is intended for installation into a Broan Model 171H rough-in housing - after the wall has been completed. The heater can be operated using its built-in thermostat or a remote thermostat (Broan Model 86 Line- Voltage Thermostat - purchase separately). The table below lists the ratings for each model. en letras oscuras. En la pagina 3, seccion “CONVERSIONES DE CABLEADO ORIGINAL” encontrara las instrucciones de conversion de vatiaje. INSTALLER: Leave This Manual With The Homeowner. HOMEOWNER: Use and Care Information on Page 3. INSTALADOR: Deje este manual con el dueno de casa. DUENO DE CASA: Informacion del uso y mantenimiento en la pagina 3. Follow these basic steps when installing this heater: • Remove the housing mask. • Fasten finish assembly inside housing. • Plug assembly in. • Attach grille and knob. INSTALL THE HEATER ASSEMBLY 1. Remove housing mask. Make sure wall has been finished (including paint or wall paper, etc.). Take out and discard the cardboard mask from inside of housing. 2. Install heater assembly into housing. Place element end of heater assembly behind the tabs on the left side of housing. Pivot the assembly in an fasten with retaining screw from parts bag. (FIG. 2) Plug wiring harness into receptacle. WIRING DIAGRAM Please refer to Figure 3 for the explanation of how this unit is wired. OPTIONAL WIRING CONVERSIONS 1. Conversion to half-wattage. (FIG. 4) The heater will produce less heat and use less electricity if converted to half-wattage. Disconnect ONE of the two (2) black wires (with insulated terminals) from the motor. 2. 120 VAC to 240 VAC Conversion (FIGS. 5 & 6) (Factory-wired 120 VAC Models 170 and 174 ONLY) These heaters can be converted to operate on 240 VAC. 1) Disconnect ONE of the two (2) black wires (with insulated terminals) from the motor. 2) Disconnect the two (2) white wires (with insu lated terminals) from each other. Do not remove the white wire from beneath plastic wire tie. 3) Connect the black wire to the white wire. NOTE: When heater is converted from 120 VAC to 240 VAC, half-wattage conversion is not possible. FIG. 2 TABS OREJETAS FASTEN TO HOUSING WITH RETAINING SCREW HERE FIJE LA CAJA CON EL TORNIL...

Descargar ahora

Introduzca dos números de la imagen: