Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
CAUTION Battery polarity must be correct or module damage will occur. • A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks. Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08 39 RED THERMOSTAT W IRE ASSEMBLY BRN RED STANDING P ILOT VALV E WHT ON /OFF PIGGYBACK W IRE Figure 10.3 Standing Pilot Ignition Wiring Diagram Figure 10.2 Intellifi re Pilot Ignition (IPI) Wiring Diagram *Note: Appliance will not operate unless properly grounded. PLUG-IN 3V TRANSFORMER ON/OFF WALL SWITCH IGNITION MODULE (3V) VALVE NEUTRAL GROUND LOW VOLTAGE SEE NOTE 1 REMOTE CONTROL HOT PLUG-IN REMOTE JUMPER WIRE ORG GRN BRN BRN RED BLK INTERMITTENT PILOT IGNITOR ORG WHT IGNITION MODULE 3 VAC TRANSFORMER VALVE 3 VAC THERMOSTAT WIRE ASSEMBLY BLACK WIRE CAN BE PLUGGED INTO ANY OF #1 - #5 LOCATIONS ON THE HOT SIDE WHITE WIRE CAN BE PLUGGED INTO ANY OF#1 - #5 LOCATIONS ON THE NEUTRAL SIDE GROUND TO FIREPLACE CHASSIS* D. Standing Pilot Ignition System Wiring • This standing pilot ignition system wiring does not require a 110 VAC supply to operate. • It is recommended that a 110 VAC junction box be installed for use with a fan or remote control. (See Figure 10.4 for junction box wiring). CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Shock hazard. • Replace damaged wire with type 105. C rated wire. • Wire must have high temperature insulation. WARNING 40 Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08 WHT WHT BLK BLK GRN wire inside box Copper ground attached to GRN screw with GRN wire 14/2WG Romex Connector If the box is being wired to a wall mounted switch for use with a fan (See Figure 10.5): • The power supply for the appliance must be brought into a switch box. • The power can then be supplied from the switch box to the appliance using a minimum of 14-3 with ground wire. • At the switch box connect the black (hot) wire and red (switch leg) wire to the wall switch as shown. • At the appliance connect the black (hot), white (neutral) and green (ground) wires to the junction box as shown. • Add a 1/4 inch insulated female connector to the red (switch leg) wire, route it through the knockout in the face of the junction box, and connect to the top fan switch connector (1/4 inch male) as shown. Red Red Black Black Green Green White White Red Black Green White SWITCH BOX JUNCTION BOX POWER SUPP LY WIRE S SWITCH MINIMUM 14-3 AWG WITH GROUND Note: Do NOT wire 110 VAC to wall switch. • Remove the screw attaching the junction box/receptacle to the outer shell, rotate the junction box inward to disengage it from the outer shell (see Figure 10.4). • Pull the electrical wires from outside the appliance through this opening into the valve compartment. • Feed the necessary length of wire through the connector. • Make all necessary wire connections to the junction box/receptacle and reassemble the junction box/receptacle to the outer shell. Figure 10.4 Junction Box Detail Figure 10.5 Junction Box Wired to Wall Switch E. Junction Box Installation F. Wall Switch Installation for Fan (Optional) Heat & Glo • 6000G, 6000G-IPI • 2103-900 Rev. M • 9/08 41 B. Facing Material Figure 11.3 Noncombustible Facing Fire Risk. Do NOT obstruct air inlet or outlet grilles. Do NOT modify grilles. • Modifying or covering grilles could cause temperature rise and fi re hazard. Finishing materials must not interfere with: • Air fl ow through grilles or louvers. • Operation of louvers or doors. • Access for service. 41 in. 39-3/8 in. NON-COMBUSTIBLE ZONE (Shaded areas) A Top V iew IN TER IOR W ALL F IREPLACE OPENING B MANTEL LEG OR W ALL PROJECTIONS Note: All measurements in inches. MEASUREMENTS FROM TOP EDGE OF THE OPENING 5 10 11 12 2-1/2 13 14 15 16 17 18 19 32 TO CEILING 9 10 11 12 8 7 6 5 4 3 25 18 Note: Measurement is taken from top of the opening, NOT the top of the fi replace. If A minimum is ____, then B maximum is_____. A Inches 2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16 Millimeters 62 87 113 138 164 189 B Inches 1 2 3 4 5 . Millimeters 25 51 76 102 127 . A. Mantel Projections Figure 11.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance. 11 Finishing Fire Risk. Finish all edges and fronts to clearances and specifi cations listed in manual. • Do NOT overlap combustible materials onto appliance front. The appliance front may only be covered with noncombustible materials. The bottom one inch of the appliance front is exempt and may be covered with either non-combustible or combustible materials. • Install combustible materials only up to specified clearances on top, front and side. • Seal joints between the fi nished wall and appliance top and s...
Otros modelos de este manual:Los acondicionadores de aire - 6000G (3.6 mb)
Los acondicionadores de aire - 6000G-IPILP (3.6 mb)
Los acondicionadores de aire - 6000G-LP (3.6 mb)