Votos - 1, Puntuación media: 4 ( )

Fabricar: Mitsubishi Tamaño del archivo: 1.31 mb Nombre del archivo: Idioma del manual:

[Refer to 5.2 Operation Status Monitor Data.! (1)[Operation Button] [Operation control] will not be displayed. Click on [Return] to end the operation status monitor and return to the Main Screen.[Refer to 3.7.1(8)] (2)[Menu Bar] [Return] , [Print] , [Graph] and [Help] are displayed on the menu bar. Neither [Graph] nor [Ref.] may be used. Other menus are same as that of other units. 32 3 Introduction to the screen Display Contents 123456789A SW1-oioooooooo SW2-000000 SW3-oooooo Set status of function selector switch 0:OFF setting 1 :ON setting SW45673 00000 Set status of extension function selector switch 0:OFF setting 1 :ON setting SWU21 Set status of M-NET address switch on LM ADAPTER SWU1:The units digit SWU2:The tens digit 1234567S9ABCDEF [M] FLAG-11000000 ERR0R-0011000000000000 [LON]FLAG-00000000 ERROR-0000000000000000 Internal processing status of LM ADAPTER FLAG:Control flag status ERROR:Error flag status [M]:M-NET communication processing flag [LON]:LonWorks communication processing flag 0: Reset 1:Set CN02-23 11 General input status of LM ADAPTER 0:Normal 1:Detecting PM, F'LR-0 Indicating power failure detecting status of LM ADAPTER 0:Powering 1 : Interrupting [nviOnOff n] 123455789A 00-0000000000 10-0000000000 ^- Unit add <— Unit address (Unit digit) ress(Tens digit) Binding information on operation command input 0:No binding 1:Binding 33 Display Contents [nvoOnOff_n] 1234S56789A 00-0000000000 10-0000000000 Unit address (Unit digit) Binding information on operation status output 0:No binding 1:Binding Unit address(Tens digit) [IC CONNECT] 123456789A 00-0000000030 5-0000000000 Unit address (Unit digit) T. Connection status of air conditioner(indoor unit) 0:Not connected 1:Connected Unit address(Tens digit) ---0* — [Rev] [Snd] St VI p VI 1-00 00 00 00 2-00 00 00 00 Unit address (Tens digit) Latest value of network variables [Rcv] Received value of operation command input [Snd] Output value of operation status St : state field data V1 : value field data Unit address(Unit digit) [Rcv] St Vl [Snd] St Vl stopping 00 00 00 00 Operating 01 C8 01 C8 [nci DATA] StarLKrtBt =1800. 0 StartOutTm =1800.0 Set value of configuration property 34 3.7.3 Trend graph Clicking IFv^IjI at 3.7.2 (2) [GRAPH] displays Trend Graph Screen. (1) Procedure for graphing (a)Click [Option] on the menu bar. (b)The sub-menu of "Graph detail setting" and "Other setting will be displayed. Click "Graph detail setting" to set each item of the graph. *Note Without setting of each item on "Graph detail setting," no graph can be displayed. (The graph detail setting is explained in (c) and other setting is in (d).) (c) Graph Detail Setting Screen will be displayed. 1) Click your desired number (from Graph 1 ~ 5) for graphing. *Note The number of the graph selected represents the ordinate. 2) Select [Unit] desired to be graphed.- 3) Select [Source] (Data item) desired to be graphed. 4) Set [Upper limit, Lower limit] of data. You may also set to [Auto-scale].- - When the data exceeds the high limit value or low limit value being set under [Auto-scale] setting, the above value is replaced by the exceeded value in the setting. When the high limit value and low limit value are set before entering, 10 will be set to the high limit value and 0 will be to the low limit value automatically. 5) [Graph upper limit, Graph lower limit] (Ordinate display position/range) may be acceptable as it is. Setting is required when the display position/range is desired to change. (To display over the entire screen, enter 100 to the graph high limit position, while 0 to the low limit position.) *Note The input of the upper limit value/lower limit value and graph upper limit position/lower limit position can be entered by the ten keys for numerical input besides the entering by the key board. 6) Click [ after completing all setting to return to Trend Graph Screen. (d) Conducting the "Other setting" With "Other setting," the optional function to facilitate graph observation can be set. Click [Option] on the menu bar. Click "Other setting." Other Setting Screen will be displayed. 1) Moving [Scroll bar] by dragging or clicking < ► changes the value of the horizontal grid line from 0 to 4. The horizontal grid line will be displayed on the graph in a number of the value above. *The sampling time can not be set by on-line. 35 2) Clicking I returns to Trend Graph Screen displaying the horizontal grid line in the number being set to the graph.---- (e) Starting the graph Clicking - - j initiates monitoring to graph the data for each one minute. The sampling time to allow graphing by online system is limited to 500 minutes ma...

Descargar ahora

Introduzca dos números de la imagen: