Votos - 1, Puntuación media: 5 ( )

Fabricar: Xpelair Tamaño del archivo: 2.68 mb Nombre del archivo: Idioma del manual:

35 Control of fan speed Fig. 36 External air intake digitemp 21 Xpelair 3.4.12 Use button T3 to select Night well-being Mode, which Night well-being includes the following functions: mode - Gradual Increase of the temperature set for cooling, - Gradual reduction of the temperature set for heating (only HP models). - Reduction of noise level. - Lower energy consumption at night. To select Night well-being mode press button T3 after selecting the operating mode using button T4 and setting the temperature using button T7. Ideally, you should start night well-being mode operation just before you fall asleep. In cooling mode, the set temperature is held for one hour after starting Night well-being mode operation. For the next hour, the setting is allowed to increase gradually up to 2°C over the original setting, while the fan speed setting is low. After the second hour, the temperature and fan speed settings are not changed. In heating mode, the set temperature is held for one hour after starting Night well-being mode operation. For the next hour the setting is lowered gradually to 4°C below the original while the fan speed setting is low. After the second hour, the temperature and fan speed settings are not changed. Night well-being mode operation is not available for dehumidifying only. Night well-being mode operation can be halted at any time (ideally when you wake up in the morning) by pressing button T3 again. At this stage the temperature and fan speed settings made prior to starting Night well-being mode operation go back into effect. Fig. 37 Night well-being mode 3.4.13 Setting programs for operation 3.4.14 Setting of correct time The air conditioner logic provides the user with a choice of two operating programs that can be set to start and stop at programmed times, for example you might want the air conditioner to start shortly before you return home so that it is cool when you get there. To use these functions it is first necessary to set the exact time on the remote control and then set the time for the programs to start. To set the exact time proceed as follows: a) Press button T6 Time and Program Setting, as many times as necessary to display the hour indicator (H). b) Press the toggle button T7 to increase or decrease the numerical display until it shows the exact hour. c) Press button T6 again to display the minute indicator (M). d) Press toggle button T7 to increase or decrease the numerical display until it shows the exact time in minutes. Fig. 38 Setting of correct time 22 -cligitemp 3.4.15 Setting of time schedules for 1st and2nd Operating Program (PROGR. 1 and PROGR.2) 3.4.16 Starting and stopping operating programs To set the times for starting and stopping the two air conditioner programs, proceed as follows: a) Press button Time and Program Setting (T6), as many times as necessary to display the PROGR 1 ON indicator (Time to start 1st program). b) Press toggle button T7 to increase or decrease the numerical display of the time when you want program 1 to start. Every time you press one end of the toggle button the time setting increases or decreases by 30 minutes. c) Press button T6 Time and Program Setting, as many times as necessary to display the PROGR. 1 OFF indicator (Time to stop 1st program). d) Press toggle button T7 to increase or decrease the numerical display of the time when you want program 1 to stop. Every time you press one end of the toggle button the time setting increases or decreases by 30 minutes. e) Press button Time and Program Setting (T6), as many times as necessary to display the PROGR 2 ON indicator (Time to start 2nd program). 0 Press toggle button T7 to increase or decrease the numerical display of the time when you want program 2 to start. Every time you press one end of the toggle button the time setting increases or decreases by 30 minutes. g) Press button T6 Time and Program Setting, as many times as necessary to display the PROGR. 2 OFF indicator (Time to stop 2nd program). h) Press toggle button T7 to increase or decrease the numerical display of the time when you want program 1 to stop. Every time you press one end of the toggle button the time setting increases or decreases by 30 minutes. i) To return to the normal operating mode just press button T6 as many times as necessary to cancel the program indications from the display. Xpelair Fig. 39 Setting of time schedules for 1st and 2nd Operating Program (PROGR. 1 and PROGR. 2) After making the settings for the operating programs, they can be used or not, as needed. Either or both of the programs can be used. In particular, when you press T11 to run the programs, the following things occur: Use of Program no. 1 only Use of Program no. 2 only Use of Programs 1 and 2 Disuse of both programs. digitemp 23 Xpelair 3.4.17 Press button T10 to reset all the settings on the remote Resetting all control. functions of This will cancel all the settings of ...

Descargar ahora

Introduzca dos números de la imagen: