Votos - 3, Puntuación media: 4 ( )

Fabricar: Daewoo Tamaño del archivo: 229.03 kb Nombre del archivo: 8a46e19a-bf28-4efa-85f8-068a8c3db7e0.pdf Idioma del manual:

ON/OFF TIMER ENTER/ CANCEL TURBO/MILD +– +– 5 SETTING THE UNIT FOR REMOTE OPERATION After the unit is fully connected and plugged in, it can be turned on. To turn the unit on and set it for remote operation, follow the procedures below: 1. Open the indoor unit’s cover and make sure the EMERGENCY/ REMOTE switch is set to the REMOTE position; this will allow the unit to operate with the remote controller. 2. Press the ON/OFF button on the remote controller to turn on the unit. The On LED will light on the indoor unit and “ON” will light in the remote display. To select the various modes and settings, read the following pages. THREE MINUTE COMPRESSOR DELAY • After turning the indoor unit on and setting it for air conditioner operation, the compressor (outdoor unit) will not come on for three minutes. This is a feature that will protect the compressor from damage due to quick start and stops. EMERGENCY/REMOTE Switch REMOCON EMERGENCY CELSIUS TO FAHRENHEIT CONVERSION CHART CELSIUS FAHRENHEIT 18 64.4 19 66.2 20 68 21 69.8 22 71.6 23 73.4 24 75.2 25 77 CELSIUS FAHRENHEIT 26 78.8 27 80.6 28 82.4 29 84.2 30 86 31 87.8 32 89.6 NOTES: • When operating the remote controller, make sure there are no obstructions between the remote controller and the remote sensor. • After a while the display goes blank to conserve battery power. To check the settings, press the ON/OFF button once. TO SET THE UNIT TO AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Follow procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Make sure the indicator appears in the remote display. Using the TEMP. or buttons, set the desired temperature. The desired temperature can be changed up or down 1 degree from the actual room temperature. For temperature setting: 24~28°C AUTO AUTO3. Then the unit will automatically operate. 6 SET UNIT TO QUICK MODE To set this unit to cool or heat (Heat pump model only) at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Press the MODE button until the Quick (“ cator blinks. ”) indi 3. The unit will then start cooling or heating the room at the highest power. TO SET UNIT TO COOL MODE To set the unit to cool the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Press the MODE button until the Cool indicator appears in the display. 3. Using the TEMP. or buttons, set the desired temperature. The desired temperature can be changed up to 32°C and down to 18°C. 4. To select the fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). AUTO FAN SPEEDS “AUTO” The fan will automatically select the fan speed. “” The fan will operate on low speed. “” The fan will operate on medium speed. “” The fan will operate on high speed. “NATURAL”The fan will randomly cycle through the speeds simulating a cool breeze. 7 TO OPERATE ONLY FAN To operate only the fan so the unit will circulate the air, proceed as follows: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Press the MODE button until the Fan indicator appears in the display. No allowance setting temperature 3. To select a fan speed, press the FAN SPEED button until the desired speed appears in the display (see below). FAN SPEEDS “” The fan will operate on low speed. “” The fan will operate on medium speed. “” The fan will operate on high speed. “NATURAL” The fan will randomly cycle through the speeds simulating a breeze. NOTE: •If “NATURAL”is selected, the NATURAL”indicator on the indoor unit will light. TO SET UNIT TO DEHUMIDIFIER MODE Select this mode when there is high humidity. To select, follow the procedures below. 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Press the MODE button until the Dehumidifier indicator appears in the display. 3. Using the TEMP. or buttons, set the desired temperature. The desired temperature can be changed up to 32°C and down to 18°C. 8 TO SET UNIT TO HEAT MODE (ONLY HEAT PUMP MODEL) To set the unit to heat the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Press the MODE button until the Heat indicator appears in the display. I...

Descargar ahora

Introduzca dos números de la imagen: