The knob selection provides settings from 1 to 6 and each increase in number equates to approximately 7°C temperature difference. Position 1 represents 7°C and would be used for frost protection when the property is not occupied. Position 3 represents 21°C and is the normal comfort position. NOTE – Should your heater fail to come on when the thermostat knob is at a low setting, this may be due to the temperature of the room being higher than the thermostat setting. Timer/Programmer A digital tim

It should only be operated when in the upright position as shown in diagram C. All models are protected against moisture ingress to IPX4 standard. All models, except those with no controls, are fitted with a 7-day digital programmer. Installation: Before connecting the heater, check that the supply voltage is the same as that stated on the rating label. When selecting the position for the heater to be installed, consideration should be given to ensure that there are no obstructions closer than t

500W Heater (refer to diagram A) If the heater is required to be fitted towards an object/obstruction to the left then the bracket should be positioned against the floor and the object/obstruction and the wall marked along the right edge of the right upright. This is the final position of the left side of the left upright member of the bracket. If the heater is required to be fitted towards an object/obstruction to the right then the bracket should be positioned against the floor and the object/

This guarantee is only applicable if the appliance has been installed in accordance with the installation/positioning instructions detailed in the booklet. To help make the best use of your Air Conditioner, please read this booklet carefully. The guarantee is subject to the provisions that the appliance: (a) Has been used solely in accordance with the User Instruction Book. (b) Has been properly connected to a suitable supply voltage as stated on the rating plate attached to the appliance.

Timer/Programmer A digital timer/programmer is built into the product and is situated behind the controls door. This will control the operation of the heater for the time periods set at the thermostat setting. Setting up If, at any time during setting, a period of approximately 7 seconds passes with no button pressed then the timer reverts to the clock display and saves the settings thus far. To set the clock, firstly press the left button below where it says “SETUP” on the display. Five options

If the heater is required to be fitted towards an object/obstruction to the right then the bracket should be positioned against the floor and the object/obstruction and the wall marked along the left edge of the left upright. This is the final position of the right side of the right upright member of the bracket. All other sizes of heaters (refer to diagram B) If the heater is required to be fitted towards an object/obstruction to the left then the bracket should be positioned against the floor

When placing the heater on the bracket, firstly engage the heater on to the bottom hooks and then press the heater on to the catches. It is recommended to press the heater at the ends and not on the grille area. 500W Heater (refer to diagram A) If the heater is required to be fitted towards an object/obstruction to the left then the bracket should be positioned against the floor and the object/obstruction and the wall marked along the right edge of the right upright. This is the final position o

PROG will be flashing at this time. Press the AFFIRM button and the 01ON display will be flashing. Press the AFFIRM button and the hour display will flash and be adjustable by the + and – buttons. Pressing AFFIRM will move the display to the minutes, and then to the days. The days have special groupings that can be selected by pressing the + and - buttons. They are MO TU WE TH FR, SA SU, MO TU WE TH FR SA, MO WE FR , TU TH SA, MOTU WE , TH FR SA, ALL DAYS and individual days. Make your selection

At this point the air conditioner is set for automatic operation under the control of the electronic thermostat, it will now maintain the room temperature at the pre-set level. Step 7 To stop the air conditioner press the green ON/OFF (J) push-button (4). DEHUMIDIFICATION MODE When you use the air conditioner in the dehumidification mode, you do not have to use the flexible air outlet tube. The unit will dehumidify and recirculate the room air. In this mode the air conditioner will reduce

The Panel -How it works A heating element within the metal case warms its front face for direct radiation into the room and a gentle circulation of warm air around the room. The built-in thermostat with its adjustment knob located behind the controls door, controls the room temperature by sensing this from the air passing upwards through the panel. The knob selection provides settings from 1 to 6 and each increase in number equates to approximately 7°C temperature difference. Position 1 represen