Votos - 5, Puntuación media: 4.4
(
)
)
|
Fotos y especificaciones Panasonic ER-GC50 |
Resumen del manual
Do not use thinner, benzine, alcohol or other chemicals. • Clean the power plug regularly to remove any dust or dirt. >Storing the clipper • Store the clipper in a place with low humidity after use. • Do not store the clipper where it will be exposed to direct sunlight or other heat sources. • Store the AC adaptor in a dry area where it is protected from damage. • Keep the oil away from children. Parts identification .. . .. . abER-GC70ER-GC50 . .. . .. . abER-GC70ER-GC50 . . . . . . A Main body 1 Dial a. Scale marks b. Instruction marks 2 Charge indicator lamp 3 Power switch [0/1] B Blade block 4 Cleaning lever 5 Moving blade 6 Stationary blade 7 Mounting hook . . . .. . C Comb attachment [A] (1 mm to 5 mm) D Comb attachment [B] (6 mm to 5 mm) E Comb attachment [C] ( 6 mm to 45 mm) F AC adaptor (RE9.49) 8 Power cord 9 Appliance plug G Oil H Cleaning brush I Travel pouch Accessories ER.GC70 C Comb attachment [A] (1 mm to 5 mm) D Comb attachment [B] (6 mm to 5 mm) E Comb attachment [C] ( 6 mm to 45 mm) I Travel pouch EnglishER.GC50 .. Charging the clipper You can fully charge the clipper in 8 hours if it is losing speed. A full charge supplies enough power for approximately 40 minutes of use. 1. Slide the power switch on the main body to the “0” position to turn off the clipper. 2. Plug in the AC adaptor into a household outlet. 3. Insert the appliance plug into the 1 2clipper. The charge indicator lamp lights and stays on until the AC adaptor is removed 3 from a household outlet. 4. Disconnect the AC adaptor from an outlet when charging is completed. When charging the clipper for the first time or when it has not been in use for more than 6 months, please charge it for 16 hours (in order to activate the rechargeable battery). If you charge the clipper with the battery completely discharged, the charge indicator lamp may not glow immediately. However, the lamp will glow normally after charging for a few minutes. AC operation English • See pages 4 and 5. 4. Slide the power switch on the the switch in the “1” position. When the attachment is mounted correctly, the dial will not turn with the switch set to “1”. You can use the clipper while charging, even if the battery capacity is low. If the clipper does not work, continue charging it for approx. 1 minute. UsingUsing comb attachments1. Slide the power switch on the main body to the “0” position to turn off the clipper. 2. Make sure there is no damage to the blade. 3. Mount the attachment and adjust the dial. main body to the “1” position to turn on the clipper. After adjusting the trimming length, make sure the attachment is fixed with 5. Cut hair to the correct height by moving the clipper back against the flow of the hair. Do not use the clipper in an inverted position. This can cut hair too deeply. 1. Cut hair by placing the clipper head directly on the scalp. Installing the attachment combComb attachment [A] (1 mm to 5 mm) 1. Align the instruction mark “” to “1”. 2. Mount the comb attachment [A] to the main body. 3. Align the instruction mark “” to the length you want to cut. Cutting length (mm) (estimate) 1 3 4 5 Scale marks 1 3 4 5 The dial will turn past the indicator “6” even when the comb attachment [A] is being used. The clipper will not cut well above 6 mm, so do not try to cut more than 6 mm with the comb attachment [A] mounted. Actual hair length will be a little longer than the height you set. • • >Trimming without attachment combs Trimming your hair without an attachment will trim hair length to approx. 0.5 mm. Comb attachment [B] (6 mm to 25 mm) Comb attachment [C] (26 mm to 45 mm) ER.GC70 2. Mount the 3. Align the comb instruction attachment [B] mark “ 1. Align the 2. Mount the 3. Align the 1. Align the instruction mark “” to “6”. to the main the length you ” to instruction comb instruction body. want to cut. mark “ ” to attachment [C] mark “ ” to “26”. to the main the length you Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks 8 9 10 11 1 • 15 • 16 10 17 • 18 • 19 • • 3 • 4 18 5 • • • • body. want to cut. 6 7 6 • Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks 6 7 6 • 13 14 • 14 33 34 • 34 0 1 • • 40 41 • Actual hair length will be a little longer than the height you set. • • 8 9 30 31 3 • 35 • 36 30 37 • 38 • 39 • 4 • 43 • 44 38 45 • 4 • • 45 • Actual hair length will be a little longer than the height you set. English English Cleaning Cleaning with brush 1. Disconnect the power cord from the clipper. Be sure to set the switch to “0” before you remove the blade. 2. Remove the comb attachment. 3. Hold the main body, place your thumb against the blades and then push them away from the main body. • 4. Brush off any hair trimmings from the main body and from around the blade. 5. Brush any hair trimmings out from between the stationary blade and the moving blade while pressing down the c...
Otros modelos de este manual:Herramientas de cosméticos - ER-GC70 (1.56 mb)