Votos - 5, Puntuación media: 4.4
(
)
)
|
Fotos y especificaciones Panasonic ER-GC70 |
Resumen del manual
Align the 2. Mount the 3. Align the 1. Align the instruction mark “” to “6”. to the main the length you ” to instruction comb instruction body. want to cut. mark “ ” to attachment [C] mark “ ” to “26”. to the main the length you Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks 8 9 10 11 1 • 15 • 16 10 17 • 18 • 19 • • 3 • 4 18 5 • • • • body. want to cut. 6 7 6 • Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks Cutting length (mm) (estimate) Scale marks 6 7 6 • 13 14 • 14 33 34 • 34 0 1 • • 40 41 • Actual hair length will be a little longer than the height you set. • • 8 9 30 31 3 • 35 • 36 30 37 • 38 • 39 • 4 • 43 • 44 38 45 • 4 • • 45 • Actual hair length will be a little longer than the height you set. English English Cleaning Cleaning with brush 1. Disconnect the power cord from the clipper. Be sure to set the switch to “0” before you remove the blade. 2. Remove the comb attachment. 3. Hold the main body, place your thumb against the blades and then push them away from the main body. • 4. Brush off any hair trimmings from the main body and from around the blade. 5. Brush any hair trimmings out from between the stationary blade and the moving blade while pressing down the cleaning lever to raise the moving blade. Cleaning in water The mark on the left means suitable for cleaning under an open water tap. Warning Disconnect the power cord from the clipper before cleaning it in water to prevent electric shock. 1. Disconnect the power cord from the clipper. 2. Remove the blade. 3. Rinse off any hair trimmings that are sticking to the blades with running water. 4. Rinse out any hair trimmings that are inside the clipper with running water. 5. Gently shake the clipper 4 or 5 times and then wipe off any water drops from the clipper and the blade. 6. Place the clipper on a towel with the power switch on the main body facing downwards to let it dry fully. Lubrication Apply the oil to the clipper before and after each use. Apply a drop of the oil to the points indicated by the arrows. Remounting the blade Fit the mounting hook into the blade mounting on the clipper and then push in until you hear a click. >Blade life Blade life will vary according to the frequency and length of use. It is expected to be about years when using the clipper twice a month for 0 minutes each time. If cutting efficiency is reduced despite proper maintenance, change the blades. >Battery life Battery life will vary according to the frequency and length of use. If the batteries are charged 3 times a month, the service life will be approximately 3 years. • It is recommended that the clipper be recharged at least every 6 months even when not in regular use because the charge will drain from the battery and its service life may be shortened. Disposal of the clipper battery Remove the built.in rechargeable battery before disposing of the clipper. Please make sure that the battery is disposed of at an officially designated location if there is one. Do not dismantle or replace the battery so that you can use the clipper again. This could cause fire or an electric shock. Replace it at an authorized service center. • Disconnect the power cord from the clipper when removing the battery. • Discharge the battery completely before removing it. • Be careful not to short the + and – terminals of the battery after removing it. • Perform steps 1 to 8 and lift the battery, and then remove it. 1.Disconnect the power cord from the clipper. .Remove the blade from the clipper. Remove the screws (a). 3.Remove the screw (b). 4.Detach the dial cover (c), remove the screw (d) and disconnect the dial (e). 5.Detach the housing (f). 6.Remove the screws (g). 7.Disconnect housing (h). 8.Disconnect the battery chamber (i) and remove the battery (j). English WARNING Do not attempt to replace the battery for the purpose of reusing the clipper. This could result in the risk of fire or electric shock. Important notice regarding environmental protection The built.in rechargeable Nickel.Metal Hydride battery contains substances that may be environmentally harmful. Please remove the battery before discarding your clipper. For environmental protection and recycling of materials This clipper contains a Nickel.Metal Hydride battery. Please make sure that the battery is disposed of at an officially assigned location, if there is one in your country. Specifications Power source Motor voltage Charging time See the name plate on the AC adaptor. (Automatic voltage conversion) 1. V DC Approx. 8 hours This product is intended for household use only. Русский Благодарим Вас за выбор машинки для стрижки волос Panasonic. Перед использованием прочитайте полностью все инструкции. Важная информация Данная машинка оснащена встроенным аккумулятором. Не бросайте в огонь, не нагревайте, а также не заряжайте, не используйте и не оставляйте прибор в месте с высокой температурой. >Испо...
Otros modelos de este manual:Herramientas de cosméticos - ER-GC50 (1.56 mb)