Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not force it past 5 or 1, or the speed adjusting function may no longer work. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003670 Installing or removing the bit CAUTION: • Install the bit securely. Always use only the wrench provided with the tool. A loose or overtightened bit can be dangerous. • Do not tighten the collet nut without inserting a bit or install small shank bits without using a collet sleeve. Either can lead to breakage of the collet cone. Insert the bit all the way into the collet cone. Press the shaft lock to keep the shaft stationary and use the wrench to tighten the collet nut securely. When using router bits with smaller shank diameter, first insert the appropriate collet sleeve into the collet cone, then install the bit as described above. To remove the bit, follow the installation procedure in reverse. Number RPM 1 9,000 2 12,000 3 15,000 4 19,000 5 23,000 ASSEMBLY 1 2 3 1. Wrench 2. Shaft lock 3. Lock lever OPERATION 1 1. Chip deflector 003803 CAUTION: • Before operation, always make sure that the tool body automatically rises to the upper limit and the bit does not protrude from the tool base when the lock lever is loosened. • Before operation, always make sure that the chip deflector is installed properly. Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed. Lower the tool body and move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete. When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. 001984 1 2 3 4 4 2 1. Workpiece 2. Bit revolving direction 3. View from the top of the tool 4. Feed direction 001985 1 1. Feed direction 2. Bit revolving direction 3. Workpiece 4. Straight guide 2 4 3 NOTE: • Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. • When using the straight guide or the trimmer guide, be sure to install it on the right side in the feed direction. This will help to keep it flush with the side of the workpiece. 1 2 3 4 5 1. Wing bolt (A) 2. Guide holder 3. Fine adjusting screw 4. Wing bolt (B) 5. Straight guide 1 2 3 55 mm ( 2 - 3/16" ) 55 mm ( 2 - 3/16" ) 1. More than 15mm (5/8”) 2. Straight guide 3. Wood 003677 Straight guide (optional accessory) The straight guide is effectively used for straight cuts when chamfering or grooving. Install the straight guide on the guide holder with the wing bolt (B). Insert the guide holder into the holes in the tool base and tighten the wing bolt (A). To adjust the distance between the bit and the straight guide, loosen the wing bolt (B) and turn the fine adjusting screw (1.5 mm or about 1/16” per turn). At the desired distance, tighten the wing bolt (B) to secure the straight guide in place. 003684 Wider straight guide of desired dimensions may be made by using the convenient holes in the guide to bolt on extra pieces of wood. When using a large diameter bit, attach pieces of wood to the straight guide which have a thickness of more than 15 mm (5/8”) to prevent the bit from striking the straight guide. When cutting, move the tool with the straight guide flush with the side of the workpiece. 003688 Templet guide (optional accessory) The templet guide provides a sleeve through which the bit passes, allowing use of the tool with templet patterns. 003692 1 2 3 003692 1 2 3 1. Templet guide 2. Screw 3. Base plate 003695 1 2 3 4 5 6 7 1. Bit 2. Base 3. Templet 4. Workpiece 5. Distance (X) 6. Outside diameter of the templet guide 7. Templet guide 003698 To install the templet guide, loosen the screws on the tool base, insert the templet guide and then tighten the screws. Secure the templet to the workpiece. Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. NOTE: • The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the bit and the outside of the templet guide. The distance (X) can be calculated by using the following equation: Distance (X) = (outside diameter of the templet guide – bit diameter) / 2 Trimmer guide (optional accessory) Trimming, curved cuts in veneers for furniture and the like can be done easily with the trimmer guide. The guide roller rides the curve and assures a fine cut. 1 2 3 4 5 6 7 1 2 3 4 5 6 7 Wing bolt (A) 2. Guide holder 3. Fine adjusting screw 4. Wing bolt (B) 5. Wing bolt (C) 6. Trimmer guide 7. Guide roller 1 2 1. Bit 2. ...
Otros modelos de este manual:Tratamiento de la madera de placas - 3612C (179.24 kb)