50317 1 2 3 Craftsman DeWalt DW 625 DeWalt DW 621 Hitachi M12V Hitachi TR12 Makita 3612 Porter Cable 6931 Porter Cable 7538 / 7539 Porter Cable Ryobi RE 600 7529 / 8529 © 2000-2005 Router Technologies All Rights Reserved Installation Instructions: Visit our Website @ Craftsman 27505-27506-27510-27511 -- ( 8-9-10 ) De Walt DW 625 & ELU 3337- 3338-3339 -- ( 11-12-13 ) De Walt DW 621 -- ( 14-15-16 ) Freud FT 2000 -- ( 17-18-19 ) Hitachi M12V -- ( 20-21-22 ) Hitachi TR12 -- ( 23-24-25 ) Makita 3612

CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded, resulting in tool malfunction. • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work. CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003671 Installing or removing the bit CAUTION: • Use always a collet which is suitable for th

SYMBOLS USD101-2 The followings show the symbols used for tool. V ....................... volts ................alternating current A .......................amperes n....................no load speed ° Hz ..................... hertz .../min................revolutions or reciprocation per minute FUNCTIONAL DESCRIPTION 003654 12 3 4 7 6 5 1. Lock lever 2. Adjusting knob 3. Depth pointer 4. Fast-feed button 5. Stopper pole 6. Fast-feed button 7. Stopper pole setting nut 003656 1 1. Nylon nut CAUTIO

Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, move the switch lever to the I (ON) position. To stop the tool, move the switch lever to the O (OFF) position. Motor unit cord 2. Outlet 3. Lock button 4. Switch trigger 003663 For RD1100 and RD1101 1 CAUTION: • Before plugging in the tool, always check to see that the 2 switch trigger actuates properly and returns to the “OFF” 3 position when released. 4 • Switch can be locked in “ON” position f

They may cause cracks in the tool base. 16. Draw attention to the need to use cutters of the correct shank diameter and suitable for the speed of the tool. 17. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD101-2 The followings show the sym

If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended GROUNDING INSTRUCTIONS This tool should be grounded while in use to protect the operator from electric shock. The tool is equipped with a three-conductor cord and three-prong grounding t

Do not force it past 6 or 1, or the speed adjusting function may no longer work. ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing the bit CAUTION: • Do not tighten the collet chuck without inserting a bit, or the collet chuck will break. • When using bit of bigger than 1-1/4” in diameter, install base plate with center hole diameter 2-1/2”, replacing the original base plate. 003672 First, remo

14. Nunca ponga las manos bajo las piezas de trabajo mientras la hoja este girando. 15. No deje la herramienta en funcionamiento sin supervision. 16. Asegurese siempre de que la herramienta este desconectada y desenchufada antes de efectuar cualquier ajuste o substituir la hoja. 17. No utilice discos de corte embotados o danados. 18. No utilice la herramienta con guardas danadas. GUARDE ESTAS INSTRUCCIONES. INTRUCCIONES PARA EL FUNCIONAMIENTO INTRUCCIONES PARA EL FUNCIONAMIENTO Cuando la bolsa d

17. Algunos materiales contienen sustancias quimicas que podran ser toxicas. Tome precauciones para evitar la inhalacion de polvo y el contacto de este con la piel. Siga los datos de seguridad del abastecedor del material. GUARDE ESTAS INSTRUCCIONES AVISO: El MAL USO o el no seguir las normas de seguridad establecidas en este manual de instrucciones puede ocasionar graves heridas personales. 19 SIMBOLOS SIMBOLOS 2 A continuacion se muestran los simbolos utilizados para la herramienta. V.........