Consider existing and anticipated machine needs, size of material to be processed through each machine, and space for auxiliary stands or work tables. Also, consider the relative position of each machine to one another for efficient material handling. Lighting And Outlets Lighting should be bright enough to eliminate shadow and prevent eye strain. Electrical circuits should be dedicated or large enough to handle the amperage draw. Outlets should be located near each machine so power or extensi

INSTALACION DE UNA BROCA DE FRESADORA Coloque la fresadora en posicion invertida o apoyela sobre uno de sus lados de manera que la base este descansando sobre el banco. Otra opcion es quitar el motor de la base antes de instalar la broca. 1. Quite el protector antivirutas (o basculelo hacia arriba si la base de descenso vertical esta colocada). 2. Sujete el eje del inducido en su sitio con la llave de eje (Fig. 4). 3. A continuacion, utilice la llave de portaherramienta para aflojar el ensamblaj

It lists causes of minor operating problems that you can correct yourself. IF YOU NEED SERVICE We're proud of our service and want you to be pleased. If for some reason you are not happy with the service you receive, here are some steps to follow for further assistance. FIRST, contact the people who serviced your unit. Explain why you are not pleased. In most cases, this will solve the problem. NEXT, if you are still not pleased, write all the details, including your telephone number, and send i

• If required, the plunge depth can be set accurately to within 0.1 mm. • Retighten button 9. Adjustment using the revolver- depth stop The revolver-depth stop enables you to quickly choose between six different cutting depths. These are also determined by the adjustment of the depth stop (10). • Adjust the required cutting depth by rotating the revolver-depth stop (21). Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 15 Helpline No.

Proceed as follows: 6. Rotate the cutterhead (using the pulley) until the tip of the knife is at the top of the cutterhead arc. Place the knife setting gauge (Figure 17) over the cutterhead so the tip of the knife contacts the center of the gauge, and all four "feet" of the gauge rest firmly upon the cutterhead, as the knife is pushed down into its slot. The gauge will set the knives at approximately .070" above the cutterhead. Knife height should not vary more than .002-.003" across the length

Usually this will be a server owned by the ISP. Get this IP address from your ISP. This is the second choice for a DNS server. Get this IP address from your ISP. The Maximum Transmission Unit size may be changed if you want to optimize efficiency for uploading data through the WAN interface. The default setting (1400 bytes) should be suitable for most users. Some user may want to adjust the setting to optimize performance for wireless traffic or when low latency is desired (such as with Internet

Tool, Inc, 714 W, Grant 602-624-5248 Tucson 05719 Western Tool Inc, 702 So Campbell 602-804-0504 ARKANSAS Ft Smilh 72901 Tool Service Co, 4420 Wheeler Avenue 501-648-3125 Little Rock 72202 Eleclric Tool Service 1419 Wesl 10th Slreet 501-374-8180 CALIFORNIA City ol Industry 91745 Porter-Cable Corporalion 1305 John Reed Court 818-333-3566 Concord 94520-5679 California Electric Service 1170-G Burnell Avenue 415-827-1011 Fax: 415-827-5409 Covina 91723-3536 California Eleclric Service 61

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjust

The stopper block is also convenient for making three passes with progressively deeper bit settings when cutting deep grooves. CAUTION: • When using a bit having total length of 60 mm (2 - 3/8”) or more, or edge length of 35 mm (1 - 3/8”) or more, the depth of cut cannot be adjusted as previously mentioned. To adjust, proceed as follows: Loosen the lock lever and carefully adjust bit protrusion below the tool base to the desired depth of cut by moving the tool body up or down. Then re-tighten th