Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Set material on Mount board then slide them into the opening slot 5. Finished board will exit through the rear slot of machine. 6. When finish, press the power button and turn off. * The document, which has been mounting board laminated, is pretty hot and easily bent. Try not to touch the document until it has cooled down. * When laminating to mounting board 2mm, pressure adjustment is needed for good quality lamination. 1. Unscrew 6 retaining screws of bottom and lift off top cover. 2. Locate each end of left and right pressure spring and set in the upper position, as shown. 3. Reassemble top cover with retaining screws and do lamination. *For general lamination, set pressure springs to lower position. ***LAMINATION PRESSURE ADJUSTMENT*** ***USEFUL INFORMATION*** 15 1. Cleaning rollers with a clean and thick paper 1) If film adhesive apears on the laminated pouch surface, Insert a sheet of clean, thick paper (about 0.5mm(1/50") thickness) into the machine 2~3 times on 100.(212.) setting. The paper will attract the excess adhesive from the roller. 2. Cleaning rollers with cleaning solvent. 1) When rollers are hot, turn on and set "COLD" mode to cool them down. 2) After cooling, the machine automatically stops. 3) Unscrew 2 retaining screws on the cover by using a screw driver or a coin. Turn them towards counterclockwise. After remove them, lift off the cover. 4) Use a recommended silicon roller cleaning solvent such as Laminex Poly-Off or equivalent, on a lint-free cloth to clean residue of laminate adhesive on exposed roller surface. You can clean every corner of the rollers as turn the power switch and make them roll Prevent any liquid from spilling into the unit. 5) Re-assemble the unit in reverse-order of disassembling. * Do not turn the unit on until the rollers are completely dry. Wet rollers could cause serious harm. HOW TO CLEAN ROLLERS AND REMOVE STUCK OR JAMMED TO FILMS Roller Cover 16 IMPORTANT SAFETY CONCERNS 1. Please be cautious that neckties, necklaces, long hair and clothing are kept well away while operating the laminator. 2. Prevent children from accessing the machine. 3. Make certain that the machine is connected to an adequate power source. 4. Do not use for any purpose other than lamination. MAINTENANCE 1. Width of upper and lower side of film should be same in order not to allow melted adhesive resin to stick to the rollers. 2. Routine cleaning of rollers is required to prevent adhesive build-up. 3. Always keep the area around the machine clean. To remove dust, finger prints, etc. from housing, use diluted alcohol on lint-free cloth and do not permit liquids to get into laminator. (Do not use strong alcohol or petroleum-based cleaning solvents or abrasives.) ASSEMBLY PARTS 1. Owner's manual : 1 2. Roller cleaning papeer : (A3) 3 pcs TROUBLE SHOOTING Symptom Cause Check point * Motor doesn't work. . Power cord may not be plugged in. . Check the power cord. . Power switch is OFF . Check that the switch is on. * Film is not laminated. . Cold mode may be set. . Change the function to hot lamination * Result of lamination is not clear. . Temperature on the roller is too low or laminating is too fast. . Increase temperature or decrease speed. 17 ONE YEAR LIMITED COMMERCIAL/PROFESSIONAL WARRANTY This product is warranted for 1 year from date of purchase to be free from electrical or mechanical defects in material and workmanship. Should product fail to operate during warranty period, return it, freight prepaid, to Royal Sovereign Corporation, 100 West Sheffield Avenue, Englewood, NJ 07631, for service. There will be no charge for parts and labor to repair or replace this product whthin warranty period. When returning machine, purchaser must include a photo copy of purchase receipt and a check or money order for $20.00 to cover return shipping and handling. Please include a brief note explaining the problem. This warranty is voided in cases of improper use, abuse, mishandling and unauthorized modifications or repairs. This warranty does not cover suitability of this product for specific applications. Determining suitability of each application is solely the reponsibility of the user. This warranty does not cover incidental or consequential damages resulting from its use. This warranty is not to be considered a service contract, and does not cover routine adjustment, cleaning, jams or removal of materials that have become stuck inside machine. This warranty does not cover damage or injury resulting from improper use or failure to follow the instruction manual provided. In no event will manufacturer, importer, warranty service center, its agents or assigns, be liable for losses, either direct or indirect, including but not limited to special, incidental, consequential, or punitive damages whatsoever incurred arising out of any breach of warranty by manufacturer, importer, warranty service center, their heirs or assigns or successors in interest. Purchaser hereby accepts and agrees to these cond...
Otros modelos de este manual:Laminador - 900N 1 (1.03 mb)
Laminador - 900NPH-1200N (1.03 mb)