Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Royal Sovereign Tamaño del archivo: 708.46 kb Nombre del archivo: dfb81146-7f16-41a7-a36a-d001b2d2ab54.pdf Idioma del manual:

Once all correct settings are displayed, you may use the foot pedal to operate the laminator for “Hands Free Operation.” To activate the machine, press the foot pedal once and then release. Repeat to stop the rollers. USING REMOTE CONTROL Located on the left hand side of the rear of the laminator, to use press: 1. RUN : To activate the rollers. 2. STOP : To stop the rollers from turning. 3. REV : To reverse the rollers. Press and hold the button (useful for jams or mis-feeds of media). 10. USING CROSS CUTTER The cross cutter is located on the rear exit table of the machine 1. After lamination, move the cutter approximately to the center of the completed application at the desired point of detachment (Figure 1). 2. Grasp film with one hand, press the cutter downward into the application and slide it first to one end of the application, then to the other end to complete the cut (Figure 2 & 3). Figure 1 Figure 3 9 RSS, RSR, RSH Series 11. USING SLITTER Only the RSR & RSS series have slitters included 1. Adjust the left and/or right slitters by loosening the slitter adjuster knob (located between the front and rear rollers.) Figure 1 2. Activate the slitter by turning the slitter knob(located on the left side of the machine) clockwise. Figure 2 3. Once you activate the slitter then you can begin lamination. Figure 3 4. To deactivate the slitter turn the slitter knob counterclockwise. Figure 4 NOTE: When the slitter becomes dull break off the blade. Loosen the screw to pull down a new blade. Once the new blade is down tighten the screw. Figure 5 CAUTION When the slitters are not in use please keep the slitters positioned at the far left and right side to avoid injury. 10 Sovereign 12. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading films to upper and lower film shafts: (See page 5 for assistance with parts identification.) 1. Remove the upper and lower film shafts from the machine and load the films (do not tighten the core screws at this time). Note the direction of the adhesives on the lower and upper films (Figure 1 &2). Figure 1 2. Center the upper roll on the shaft, and then tighten the upper bolt core screws (Figure 3). 3. Load the upper and lower film shafts on the machine (Figure 4 & 5). Figure 4 Figure 5 11 RSS, RSR, RSH Series 13. THREADING FILM 13.1 Lamination and Encapsulation UPPER ROLL FILM UPPER IDLE BAR HOT ROLLEI LOWER ROLL FILI I IDDCD DOI I Eli >1 LOWER IDLE BAR RSH Series RSR Series LOWER ROLL RSS Series Thermal Lamination 1. Turn the power switch on (“I” position). Power switch is located in the rear of the unit on the left side. 2. Complete the steps on “Loading films to upper and lower film shafts” - Page 11 3. Set the rollers temperature to the recommended film temperature. 4. Take off the Paper Guide and the Front Table. 5. Pull down the upper film over the Safety Cover to the lower film; align and center the lower film to upper film and tighten the two lower bolt core screws (Figure 1). 6. Rewind the upper film back until the film aligns with the Safety Cover. 7. Thread the film over the Upper Idle Bar and underneath the Safety Cover until the film rests on the upper roller (Figure 2). 8. Carefully pull up the laminate from the lower roll around the back side of the lower idler (Caution: lower roller may be hot). 9. Tack the lower film to the upper film that is resting on the main roller (Figure 3). Figure 1 Figure 3 12 ¿RS§3SUp ...

Descargar ahora

Introduzca dos números de la imagen: