Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la knorme NMB-003 du Canada. ®l"s7oi«Se>nUa > CD О о GQC. Pinnacle 27 Е?\оай ' Roll Laminator 1 оо о о О) СП со оо 00 00 Important Safety

The heat shoes can reach temperatures in excess of 300°F. • Keep hands and fingers away from the path of the sharp film cutter blade located at the film exit. • Do not place the laminator on an unstable cart, stand or table. An unstable surface may cause the laminator to fall resulting in serious bodily injury. Avoid quick stops, excessive force and uneven floor surfaces when moving the laminator on a cart or stand. »Do not defeat or remove electrical and mechanical safety equipment such as i

Center the film and tighten the core screws (Figure 2). 3. Load a roll of mounting film or roll of craft paper to the bottom film shaft. Do not tighten the core screws at this time.(Figure 3) Note: Please see the direction of the film on the top and bottom shafts. 4. Load the top and bottom film shafts onto the machine (Figure 4 & 5). 10 ¿RS§s£™9„ 12. THREADING FILM only RSC-1650HR 12.1. Decaling 1. Turn the power switch on (“I” position). The Power switch is located on the rear left si

(RSC-1650H and RSC-1650HR). Control Buttons 1. TEMPERATURE DISPLAY: Display’s current temperature (RSC-1650H and RSC-1650HR) 2. SPEED DISPLAY: Display’s current Speed. 3. TEMPERATURE BUTTON- (RSC-1650H and RSC-1650HR): To change the temperature (max. RSC-1650H: 122°F, 50°C/RSC-1650HR: 266°F, 130°C)ofthe upper roller, press up or down arrow button. 4. SPEED BUTTON: Adjusting the speed of the rollers. To change the speed of the rollers, press the up or down arrow button. 5. RUN: To start the

(Figure 3) 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). (Figure 4) 11. Reinstall the Feed Table and the Frame-Paper Guide,and close the Safety Cover. 12. Adjust the nip setting to appropriate gap. 13. Insert and push the leader board until they reach the front nip point. 14. Push the Run button. 15. Push the leader board into the rollers. (Figure 5) Figure 5 16. Adjust the top and bott

Toque para reproducir de forma aleatoria. E S ES- Informacion sobre el trafico con Restablecimiento de la unidad un receptor FM TCM Traffic nuvi Para acceder a los datos de FM TCM Si la unidad nuvi se bloquea, apague la unidad Traffic, conecte un receptor de trafico GTM nuvi y, a continuacion, vuelva a encenderla. al conector mini-USB que se encuentra en Si de esta forma no se resuelve el problema, el lateral de la unidad nuvi. Para ver mas restablezca la unidad nuvi: informacion sobre los recep

Usuarios de nuvi 350: puede acceder al E S ES- E S archivo en PDF del manual del usuario en la memoria interna de la unidad nuvi. Consulte la pagina 7 para obtener mas informacion. Busqueda de un destino 1. En la pagina de menus, toque A donde. 2. Si es necesario, seleccione una categoria y subcategoria. Toque y para ver mas opciones. 3. Seleccione un destino. 4. Toque Ir. 5. Disfrute de la ruta. A medida que se desplaza, la unidad nuvi le guia a su destino mediante indicaciones de voz, flechas