Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Then, screw one Hex Nut (part #2B) onto the threads of each of the four Leveling Feet. (See Figure B, and Assy. Diagram B.) 7. Move the Leg Assembly to the desired floor surface working location. Adjust the Leveling Feet (part #1B) so that the entire Leg Assembly stands level. Then, firmly tighten all hardware, using an appropriate size wrench (not provided). (See Figure B, and Assy. Diagram B.) To Mount The Leg Stand On The 10" Table Saw Base: 1. With assistance, place the 10" Table Saw upside down on a flat, level, smooth surface (i.e., cardboard) on the floor. Then, place the Leg Assembly upside down on the Base (part #1G) of the 10" Table Saw. (See Figure D.) 2. Align the two mounting holes on the each of the two End Braces (part #6B) with the two mounting holes on each end of the Base (part #1G). Secure the End Braces to the Base, using four Hex Head Bolts (part #8B), eight Washers (part #3B), and four Hex Nuts (part #2B). (See Figure D, and Assy. Diagram B.) 3. NOTE: Leave the 10" Saw Table upside down for the next assembly procedure. SKU 46813 PAGE 10 END BRACE (#6B) END BRACE (#6B) MOUNTING HOLES HEX NUT (#2B)WASHER (#3B) BASE (#1G) HEX HEAD BOLT (#8B) BASE (#1G) FIGURE D To Assemble The Extension Tables: 1. With the 10" Table Saw upside down, align the right and left side Extension Tables (part #5H) with the right and left ends of the Table Saw (with the beveled edges in front). (See Figure E, and Assy. Diagram H.) 2. Align the four mounting holes in each Extension Table (part #5H) with the four mounting holes on each end of the 10" Table Saw. Then secure the Extension Tables to the Table Saw, using four Hex Head Bolts (part #11H), eight Washers (part #12H), and four Hex Nuts (#13H). (See Figure E, and Assy. Diagram H.) 3. With assistance, stand the 10" Table saw upright. To Attach The Front Rail: 1. Insert five Square Head Bolts (part #10H) through the mounting holes in the front edges of the 10" Table Saw and Extension Tables (part #5H). Allow the bolt heads to extend out about 1/2". (See Figure F, and Assy. Diagram H.) 2. Loosely attach a Washer (part #12H) and Hex Nut (part #13H) to each Square Head Bolt (part #10H). (See Figure F, and Assy. Diagram H.) SKU 46813 PAGE 11 EXTENSION TABLE (#5H) HEX HUT (#13H) WASHER EXTENSION TABLE (#5H) HEX HUT (#13H) WASHER (#12H) HEX HEAD BOLT (#11H) FIGURE E 10” TABLE SAW EXTENSION TABLE (#5H) HEX NUT (#13H) SQUARE HEAD BOLT (#10H) EXTENSION TABLE (#5H) FIGURE F WASHER (#12H) SKU 46813 PAGE 12 WASHER (#12H) (UPPER SLOT) SQUARE HEAD BOLT (#10H) 3. NOTE: The back side of the Front Rail (part #7H) has two slots. Slide the upper slot of the Front Rail over the Square Head Bolts (part #10H). (See Figures F, G, and Assy. Diagram H.) (FRONT EDGE) 10” TABLE SAW/EXTENSION TABLES (#5H) HEX NUT (#13H) FRONT RAIL (#7H) SEMI-CIRCLE HEAD SCREW (#2E) SWITCH PLATE (LOWER SLOT) (#3E) FIGURE G SQUARE NUT(#4E) 4. To align the Front Rail (part #7H), match the 7-1/8" mark on the right scale with the right edge of the 10" Table Saw Base (part #1G). (See Figure H, and Assy. Diagram H.) 5. Wrench tighten all five Square Head Bolts (part #10H). (See Figures F, G, and Assy. Diagrams G, and H.) 6. Secure the Right/Front End Cap (part #8H) and Left/Front End Cap (part #9H) to the Front Rail (part #7H), using one Tapping Screw (part #1H) on each end. (See Assy. Diagram H.) To Attach The Rear Rail: 1. NOTE: The procedure for attaching the Rear Rail (part #3H) to the 10" Table Saw is similar to that of attaching the Front Rail (part#7H) to the Table Saw. (See “To Attach The Front Rail” section, Figures I, J, and Assy. Diagram H.) 2. Insert five Square Head Bolts (part #10H) through the mounting holes in the rear edges of the 10" Table Saw and Extension Tables (part #5H). Allow the bolt heads to extend out about 1/2". (See Figures I, J, and Assy. Diagram H.) SKU 46813 PAGE 13 3. Loosely attach a Washer (part #12H) and Hex Nut (part #13H) to each Square Head Bolt (part #10H). (See Figures I, J, and Assy. Diagram H.) BASE (#1G) (RIGHT EDGE) EXTENSION TABLE (#5H) 4 5 6 7 8 9 SCALE (#6H) 7-1/8” MARK, RIGHT SCALE FIGURE H 10” TABLE SAW REAR RAIL (#3H) BASE (#1G) EXTENSION TABLE (#5H) 2-1/2” FIGURE I 4. NOTE: The back side of the Rear Rail (part #3H) has one slot. Slide the slot of the Rear Rail over the Square Head Bolts (part #10H). (See Figures I, J, and Assy. Diagram H.) SKU 46813 PAGE 14 10” TABLE SAW/EXTENSION TABLES (#5H) (REAR EDGES) REAR RAIL (#3H) SLOT SQUARE HEAD WASHER (#12H) HEX NUT (#13H) BOLT (#10H) FIGURE J 5. Wrench tighten all five Square Head Bolts (part #10H). (See Figures I, J, and Assy. Diagram H.) To Attach The Rip Fence And Miter Gauge: 1. Hook the Lock Block (part #7C) under the Rear Rail (part #3H). Then, lower the front of the Rip Fence (part #10C) into the groove on the Front Rail (part #7H). (See Figures K, L, and Assy. Diagrams C, and H.) 2. NOTE: The Rip Fence (part #10C) can be removed and reinstalled on the left side of the 10" Table Saw. In this case, the Rip Fen...