Votos - 2, Puntuación media: 4 ( )

Fabricar: Desa Tamaño del archivo: 3.76 mb Nombre del archivo: Idioma del manual:

5. Remove the burner inlet fitting from the gas control assembly (see Figure 8). DO NOT remove the orifice from this fitting. The propane/LP burner inlet fitting is included in the hardware kit (see Figure 9). 6. Be sure to use the correct orifice for your appliance. The orifice kit included with this appliance contains an orifice installed in an air mixer fitting. 7. Using thread sealant (resistant to the action of propane/LP gas) on smaller end of fitting, screw the burner inlet fitting into the outlet side of the gas control (see Figure 8). Tighten using a wrench. 8. Thread gas control valve and burner inlet fitting into burner manifold (see Figure 8). Use thread sealant on male threads of burner inlet fitting. Secure with a wrench. Make sure control rod is facing the front (see Figure 8). Figure 11 - Installing Propane/LP Pilot Orifice Pilot Injector Pilot Adjustment Screw Pilot Bracket 9. To adjust regulator pressure, remove the brass hex plug from regulator (see Figure 10). 10. Remove the plastic pressure button from the brass plug (see Figure 10). 11. Reverse the plastic pressure button and replace it into the brass plug (see Figure 10). 12. Replace brass plug into regulator. 13. Using two screws removed in step 2, page 6, replace valve cover. 14. Gently loosen and remove the pilot line connection from the pilot bracket (see Figure 11). 15. Replace injector with propane/LP injector with red stripe. 16. Replace and tighten pilot line to bracket. 17. Using screws removed in step 2, page 6, reattach pilot bracket to valve cover. 18. Continue with step 1 under Hearth Pan Installation, page 6. Control Rod Control Valve 901268-01D 8 Forr morre iinfforrmattiion,, viisiitt INSTALLATION Testing Burner for Leaks Adding Pan Material Installing the Grate and Logs INSTALLATION Continued TESTING BURNER FOR LEAKS 1. Generously apply noncorrosive leak detection fluid to all connections. WARNING: Never check for gas leaks with open flame. 2. Light the burner with the shutoff valve no more than half open and holding a match slightly in front of the pan (see Lighting Instructions, page 9). 3. Inspect all connections for bubbles, raw gas odor, or flame from any area other than the burner (leaks). If leaks are detected, shut off the gas valve immediately. Tighten, or reassemble the loose connection(s) using pipe joint compound until burner system is leak free. 4. When the burner is tested and leak free, observe the individual tongues of flame on the burner. Note: The burner design includes more ports on the outside of the bar. Make sure that all ports are clear and producing flame evenly across the burner. If any ports appear blocked, clear them by removing the burner manifold and reaming the ports with a modified paper clip or other suitable tool. 5. When finished testing, turn the gas shutoff valve OFF to extinguish all flames. ADDING PAN MATERIAL 1. Open the bag of ash bed material (vermiculite) and spread it evenly across the burner pan to the top. You may overflow the front and sides of the pan to cover the entire pan. Do not cover valve or inlet fitting. 2. Open the glowing embers and evenly cover the ash bed material (vermiculite) in the burner pan. INSTALLING THE GRATE AND LOGS 1. Place the grate over the burner pan where the two outer horizontal supports on the grate fit into the two pan positioning notches in the rear vertical edge of the pan. 2. Slide the two rear log grate steps over the two outer horizontal supports on the grate as shown in Figure 12. 3. Place the back log on the grate onto the grate steps (see Figure 13). 4. Place the front log(s) on the grate and slide forward against the front bars on the grate (see Figure 13). 5. Place the smaller top logs onto the bottom logs (see Figure 14). Leave as much open space between logs as possible to minimize flame impingement and sooting. Note: Logs may chip if they are handled roughly or if hit together while being placed. Figure 12 - Installing Grate (Pan Material...

Descargar ahora

Introduzca dos números de la imagen: