Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
SELECT BUTTON Press it can select VOL/BAS/TRE/BAL/FAD, and with the +/- button to adjust them, and the word which function it is selected will be indicated on LCD. 2. POWER BUTTON Press it to select you desired radio band and the word which band is selected will be indicated on LCD. (NOTE: When it is off, you can press any button to turn on the unit.) 3. MANUAL TUNING UP/DOWN BUTTON Press them to tune up or down, and the current frequency appears on LCD. 4. EJECT BUTTON Push it to eject the tape. 5. CASSETTE DOOR COMPARTMENT 6.FAST FORWARD/REWIND PROGRAM BUTTONS Push the fast forward and rewind buttons together to switch from one side of the tape to the other. 7. LCD (LIQUID CRYSTAL DISPLAY) 200K 50K 10K 9K USA EUROPE IMPORTANT: This radio is set to USA frequency by factory, if European frequency is required please flip the frequency step switch on the side of the unit. SPECIFICATION GENERAL Power Supply The Main Unit.........................DC 13.8 Volts. Negative Ground Maximum Output Power................................................................40W X 4 Unit Dimension.....................................................181(W) x 181(D) x 53(H) FM SECTION Frequency Range.......................................................87.5MHz - 107.9MHz MW SECTION Frequency Range...........................................................530KHz - 1710KHz LW SECTION(OPTION) Frequency Range............................................................144KHz - 290KHz PRECAUTIONS AND MAINTENANCE .1.This unit is designed for negative ground operation only. The equipment can be used safely, if the negative terminal of the battery is connected to the vehicle metal work. 2.Do not use speakers of impedance less than 4 ohms; and allow the speaker wires to be shorted together when the unit is switched on. Otherwise it may overload or burn out the power amplifier stage. 3.If the car interior is extremely hot, as after being parked in the sun, do not use the player until the car has been driven for a while to cool off the interior. 4.Take care of your tape cassette to preserve the quality of the recordings. Do not allow them to be exposed to direct sunlight. Store them in a place protected from dirt and dust and avoid handing with greasy or oily hands. Also, keep the away from magnets, and motors of the permanent magnet type. 5.It is not advisable to use cassette tapes longer than C-60(30 minutes per side) in automobile players, since the tape is too thin and tends to become easily entangled. Always remove cartridge from your tape player as soon as play is finished. 6.The capstan and tape head should be cleaned about once every six months with a soft cloth or cotton-wool swab, moistened with alcohol. This will serve to maintain the richness and clarity of sound, and prevent loss of volume. Do not use a screwdriver, or ferrous metal rod , in carrying out the above cleaning. See illustration. 7.A loosely wound cassette tape will get damaged. Prior to using such tape, tighten it in a manner as guided by Fig. 2.A carelessly would cassette tape will cause unnecessary pressure on the tape resulting in the cassette springing out while the tape is running .For prevention, rewind the tape through fast for warding or rewinding. 14. LOUDNESS BUTTON press it to get the best loudness quality during it is for bass.And word LOUD will appear on LCD. 15. 1-6 PRESET BUTTONS Press them to recall all storage station frequency which will appear on LCD, stations can be memorized in band. 8. BAND BUTTON Press it to select you desired radio band and the word which band is selected will be indicated on LCD. 10. AS/PS BUTTON Press it to perform all stations memory for 5seconds each time.while memory digital and frequency will flash on LCD.If thebutton is pressed for more than2 seconds,it will seek station on current band,Then write to the preset memories and word ART willappear on :LCD.When the auto-storage operation is completed, it will automatically perform for 5seconds each time.During the memory station performing,press 1-6digital buttons to select and stop scanning function. 9. SEEK BUTTON Press it to auto seek up frequency until find the desired broadcast. 11. STEREO/MONO BUTTON Press it to change the sound effect.( Mono keep remain) 12. FREQUENCY/CLOCK SWITCH Press this button to select the display mode such as frequency display or clock display.(you can only adjust tine setting at clock display) 13. CD SWITCH 16. CD INPUT JACK 17. RET BUTTON Press it to reset the functions when programms are disorder. INSTALLATION PRECAUTIONS 1. Choose the mounting location carefully so that the unit will not interfere with the normal driving functions of the driver. 2. Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or hot air from the heater, or where it would be subject to dust, dirt or excessive vibration. 3. Use only the supplied mounting hardware for a safe and secure installation. WIRING CONNECTION ...