Votos - 4, Puntuación media: 3
(
)
)
|
Resumen del manual
Always wear protective gloves! CAUTION: Start the brush cutter only after having assembled it completely. For machines with U Handle models –Place the handle-fixing metal so that the handle with the control lever will be positioned on the right (the right-hand grip side) as viewed from the engine side, and the other handle on the left side. – Fit the groove of the handle-fixing material to the handle end. Fix provisionally the attached metal by hexagon socket bolt supplied. – Adjust the handle to an easy-to-operate position, and tighten securely the four hexagon socket bolts uniformly on the right and left by Allen wrench. – Wrap the waist pad around the shaft so that the hanger(1) will protrude through the slit in the waist pad and the control cable and the cords(3) will aiso be wrapped under the waist pad(2). For machines with Loop Handle models – Fix a barrier to the left side of the machine together with the handle for operator’s protection. – Do not adjust position of the loop handle too close to the control grip. Keep not less than 250mm distance between the handle and the grip. (a distance collar is provided for this purpose.) 9 MOUNTING OF PROTECTOR MOUNTING OF PROTECTOR To meet the applicable safety provisions, only the tool/ protector combinations as indicated in the table must be used. Be sure to use genuine MAKITA cutter blades or nylon cutting head. – The cutter blade must be well polished, free of cracks or breakage. If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately. – Polish or replace the cutter blade every three hours of operation. – If the nylon cutting head hits against a stone during operation, stop the engine and check the nylon cutting head immediately. Star Blade Eddy Blade Protector for metal blades PART NO. 6258507600 PART NO. 6258507700 PART NO. 6258061001 Nylon cutting head Protector for cord cutter PART NO. 6218016000 PART NO. 6258060001 CAUTION: The appropriate protector must always be installed, for your own safety and in order to comply with accident-prevention regulations. Operation of the equipment without the guard being in place is not permitted. – Fix the protector (1) to the clamp (3) with two bolts M6 x 30 (2). – When using the string head, fit the protector (6) into the protector (1), and tighten them with two nuts (5) and two screws (4). 10 MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD MOUNTING OF CUTTER BLADE OR NYLON CUTTING HEAD Turn the machine upside down, and you can replace the cutter blade or the nylon cutting head easily. – Insert the hex wrench through the hole in the gear case and rotate the receiver washer (3) until it is locked with the hex wrench. – Loosen the nut (1) (left-hand thread) with the socket wrench and remove the nut (1), and clamp washer (2). With the hex wrench still in place. – Mount the cutter blade onto the shaft so that the guide of the receiver washer (3) fits in the arbor hole in the cutter blade. Install the clamp washer (2) and secure the cutter blade with the nut (1). [Tightening torque: 13 - 23 N-m] NOTE: Always wear gloves when handling the cutter blade. NOTE: The cutter blade-fastening nut (with spring washer) is a consumable part. If there appears any wear or deformation on the spring washer, replace the nut. NOTE: The clamp washer (2), and nut (1) are not necessary for mounting the nylon cutting head. The nylon head should go on top of the receiver washer (3). – Screw the nylon cutting head onto the shaft. – Make sure that the blade is the left way up. Rotation Hex wrench Loosen Tighten Hex wrench Loosen Tighten 11 FUELS/REFUELLING FUELS/REFUELLING Handling fuel Utmost care is required when handling fuel. Fuel may contain substances similar to solvents. Refuel either in a well ventilated room or outdoors. Do not inhale fuel vapors, avoid any contact of fuel or oil with your skin. Mineral oil products degrease your skin. If your skin comes in contact with these substances repeatedly and for an extended period of time, it will desiccate. Various skin diseases may result. In addition, allergic reactions may occur. Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water. If your eyes are still irritated, see a doctor immediately. Fuel and oil mixture The engine of the brush cutter is a high-efficiency two-stroke engine. It is run with a mixture of fuel and two-stroke engine oil. The engine is designed for unleaded regular fuel with a min. octane value of 91 RON. In case no such fuel is available, you can use fuel with a higher octane value. This will not affect the engine, but may cause poor operating behaviour. A similar situation will arise from the use of leaded fuel. To obtain optimum engine operation and to protect your health and the environment, only unleaded fuel should be used! For lubricating the engine use a two-stroke engine oil (quality grade: TC-3), which is added to the fuel. The engine has been designed t...
Otros modelos de este manual:Clippers - RBC2500 (875.45 kb)