Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING -TO REDUCE THE RISK OF INJURY, BASIC SAFETY PRECAUTIONS SHOULD BE OBSERVED. INCLUDING THE FOLLOWING: READ AND FOLLOW ALL INSTRUCTIONS. 1. DRESS PROPERLY -Do not wear loose clothing or jewelry. They can be caught in moving parts. Use safety glasses and nonskid footwear. Use of sturdy gloves is recommended. 2.STAY ALERT -Watch what you are doing -use common sense. Do not operate trimmer when fatigued. 3. DANGER -RISK OF CUT -KEEP HANDS AWAY FROM BLADES-Keep both hands on handles when power is on. Do not attempt to remove cut material nor hold material to be cut when blades are moving. Make sure trimmer is switched off and unplugged when clearing jammed material from blades. Do not grasp the exposed cutting blades or cutting edges of trimmer. CAUTION -Blades coast after turn off. 4.WARNING -TO REDUCE THE RISK OF ELECTRIC SHOCK -Don’t use trimmer in rain, in wet locations, or on wet hedges of shrubbery. Use only extension cords marked “for use with outdoor appliances” having elec- trical rating not less than rating of trimmer. Do not use damaged extension cords. Inspect cords periodically and replace if damaged. Donot abuse cord. Never carry trimmer by cord. Do not yank cord to disconnect from re- ceptacles. Keep cord away from heat, oil, and sharp edges. 5. KEEP CHILDREN AWAY -Do not permit children to contact trimmer or extension cord. Keep children a safe distance from work area. 6. USE TRIMMER PROPERLY -Use only for trimming the type of shrub, growth, and the like, described in the operating instructions. Do not abuse trimmer. Do not cut grass and weeds with this trimmer. 7. DON’T OVERREACH OR STAND ON UNSTABLE SUPPORT -Keep good foot- ing and balance at all times. 8. AVOID UNINTENTIONAL STARTING OF TRIMMER -Before plugging in trimmer, be sure trimmer switch is off. Don‘t carry trimmer with finger on switch. 9. AVOID LOCKING TRIMMER SWITCH ON -Never attempt to tape, wire or fasten the switches so as to stay in the ON position. IO. DISCONNECT (UNPLUG) TRIMMER FROM POWER SUPPLY -When not in use. Before servicing, cleaning, and the like. Total Length of Cord in Feet 25 50 100 150 - AWG Size of Cord 18 1I 16 16 14 Contact Makita Authorized or Factory Service Center if a proper extension cord cannot be found. 15. Inspect blades periodically and replace before operation if damaged. 16. Hold the tool firmly with both hands. 17. Do not leave the tool running. Operate the tool only when hand-held. 18. Attention! Do not expose this tool to rain. The tool must not be left outdoors and it must not be used when wet. 19. Be cautious not to cut through the supply cable while trimming. Pull plug immediately if the supply cable be damaged or cut. 20. When not in use, be sure to cover the blades with the blade guard. VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS. Installing grip Attach the grip onto the grooves in the tool side and secure with the two screws. WARN ING : DO NOT USE WITHOUT GRIP. Hook When using an extension cord, secure it to the tool‘s cord with the hook provided. 1 Attach the hook about 100-200 mm (4”- 8”) from the extension cord connector. This will help prevent unintentional discon- nection. Switch action To prevent the trigger from being acciden- tally pulled, a lock-off button is provided as a safety feature. To start the tool, press the lock-off button in and pull the trigger. Release the trigger to stop. Power cord II Cord connector 1 Extension cord CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the “OFF” position when released. Operation Refer to the Important Safety Instructions before operation. Do not attempt to cut branches thicker than 12 mm (15/32")diameter with this trimmer. These should first be cut with shears down to the hedge trimming level. Hold the trimmer with both hands and move it in front of your body. When operating the trimmer, keep exten- sion cord behind trimmer. Never drape it over hedge being trimmed. To cut a hedge top evenly, it helps to tie a string or cord at the desired hedge height and to trim along it, using it as a reference line. I Sturdy gloves To cut a hedge side evenly, iit helps to cut from the bottom upwards. Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job. CAUTION : 0 Be careful not to accidentally contact a metal fence or other hard objects while trim- ming. The blade will break and may cause ser...
Otros modelos de este manual:Clippers - UH6310A (633.66 kb)