Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Do not use damaged extension cords. Inspect cords periodically and replace if damaged. Donot abuse cord. Never carry trimmer by cord. Do not yank cord to disconnect from re- ceptacles. Keep cord away from heat, oil, and sharp edges. 5. KEEP CHILDREN AWAY -Do not permit children to contact trimmer or extension cord. Keep children a safe distance from work area. 6. USE TRIMMER PROPERLY -Use only for trimming the type of shrub, growth, and the like, described in the operating instructions. Do not abuse trimmer. Do not cut grass and weeds with this trimmer. 7. DON’T OVERREACH OR STAND ON UNSTABLE SUPPORT -Keep good foot- ing and balance at all times. 8. AVOID UNINTENTIONAL STARTING OF TRIMMER -Before plugging in trimmer, be sure trimmer switch is off. Don‘t carry trimmer with finger on switch. 9. AVOID LOCKING TRIMMER SWITCH ON -Never attempt to tape, wire or fasten the switches so as to stay in the ON position. IO. DISCONNECT (UNPLUG) TRIMMER FROM POWER SUPPLY -When not in use. Before servicing, cleaning, and the like. Total Length of Cord in Feet 25 50 100 150 - AWG Size of Cord 18 1I 16 16 14 Contact Makita Authorized or Factory Service Center if a proper extension cord cannot be found. 15. Inspect blades periodically and replace before operation if damaged. 16. Hold the tool firmly with both hands. 17. Do not leave the tool running. Operate the tool only when hand-held. 18. Attention! Do not expose this tool to rain. The tool must not be left outdoors and it must not be used when wet. 19. Be cautious not to cut through the supply cable while trimming. Pull plug immediately if the supply cable be damaged or cut. 20. When not in use, be sure to cover the blades with the blade guard. VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. SAVE THESE INSTRUCTIONS. Installing grip Attach the grip onto the grooves in the tool side and secure with the two screws. WARN ING : DO NOT USE WITHOUT GRIP. Hook When using an extension cord, secure it to the tool‘s cord with the hook provided. 1 Attach the hook about 100-200 mm (4”- 8”) from the extension cord connector. This will help prevent unintentional discon- nection. Switch action To prevent the trigger from being acciden- tally pulled, a lock-off button is provided as a safety feature. To start the tool, press the lock-off button in and pull the trigger. Release the trigger to stop. Power cord II Cord connector 1 Extension cord CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the “OFF” position when released. Operation Refer to the Important Safety Instructions before operation. Do not attempt to cut branches thicker than 12 mm (15/32")diameter with this trimmer. These should first be cut with shears down to the hedge trimming level. Hold the trimmer with both hands and move it in front of your body. When operating the trimmer, keep exten- sion cord behind trimmer. Never drape it over hedge being trimmed. To cut a hedge top evenly, it helps to tie a string or cord at the desired hedge height and to trim along it, using it as a reference line. I Sturdy gloves To cut a hedge side evenly, iit helps to cut from the bottom upwards. Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job. CAUTION : 0 Be careful not to accidentally contact a metal fence or other hard objects while trim- ming. The blade will break and may cause serious injury. 0 Do not attempt to trim too much at a time, or malfunction of the tool may result. 0 Overreaching with a hedge trimmer, par- ticularly from a ladder, is extremely dan- gerous. Don’t work from anything wob- bly or unfirm. MAINTENANCE CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection and maintenance. Blade maintenance After operation, clean off the blades (both sides) with a stiff brush. Then wipe the blades with a cloth and coat them with light machine oil. After use When storing the tool, use the convenient hole in the bottom of the tool handle to hang the tool on a wall from a nail or hook. The tool will stop when the carbon brushes wear to a certain length. When this occurs, both carbon brushes should be replaced. To maintain product SAFETY and RELlABl LITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION : These accessories or attachments a...
Otros modelos de este manual:Clippers - UH4510A (633.66 kb)