Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Electrolux Tamaño del archivo: 1 mb Nombre del archivo: Idioma del manual:

Saw tooth blades (24 - 80 tooth) have a central base diametre of 20mm and there- fore require the use of the appropriate size top flange to ensure a correct fit. The part number is detailed in the cutting attachment summary chart. For assembly see figures (E7, E8). 2 3 4 10 2 3 4 10 F. Starting and stopping the engine position with the other starter string ar until you encounter some r cord sharply and forcefully (to start the engine 1 5 6 7 8 9 10 11 12 14 CAUTION! Start the brush cutter in a flat place. During startup stand in a stable position. Make sure the blade or nylon string head do not touch the ground or any obstacles. when Do not pull the starter cord all the way and do not release it abruptly against the machine as this could damage it. Startup of cold engine F1. Stop switch (A) turned to "I" opposite the "STOP" mark. F2. Turn the fuel enrichment lever (B) to the closed position. F3. Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm (C). The diaphragm need not be completely filled. Push the decompression valve (D) down if your models is fitted with one. Pull the cord until the engine starts. Let the motor run for a few seconds and accelerate. This will automatically return the fuel enrichment lever to its original position. The cutting devices are now rotating. Startup of warm engine F1. STOP switch turned to "I" (START). Throttle trigger lever in minimum position (released). Enrichment lever (B) in original position. F3. Repeat item F3 in the previous paragraph. Stopping the engine F5. Turn the stop switch to "O" (STOP). ENGLISH - 6 After stopping the engine the rotating parts, firmly until they stop. In case of emergency the blade or nylon string head, keep spinning above delay can be abbreviated by scraping the by inertia for a few seconds. Grip the machine blade supporting cup parallel on the ground. G. Carburetor adjustment Your machine can be equipped with a low emis- sion carbur any adjustment of the carbur ly by an authorized service center of special equipment for ensuring the best per- formance with the lowest emissions. T of technical data. speed to the minimum, turn the screw marked (T) as shown: With the engine running and well warmed up, turn the screw (T) gently clockwise, until the engine rotates at regular speed (stead noise), without the cutting devices in motion. If the cutting devices are moving, turn the screw (T) gently counterclockwise until you obtain the proper adjustment. The correct minimum speed is shown in the instruction manual in the paragraph All the above adjustments should be made with the cutting devices correctly installed. The warranty may be invalidated due to erroneous adjustments made by personnel not belonging to authorized service centers. H. Routine maintenance 1 2 3 4 7 9 10 See "Environmental information". Periods of prolonged disuse Contact your Service Center for a complete overhaul, replacement of the fuel filter and cleaning of the parts inside the machine. This will reduce the possibility of unexpected problems and will ensure the good performance and long life of your machine. Every three months Replace the spark plug. After 100 hours of use etor adjustment, the percentage of oil in the fuel mixture and make sure the oil is of excellent quality and suitable for two-stroke engines. ough hole (C). Remove and clean the spark plug (set the space between the electrode at 0.5/0.6 mm). Replace if excessively encrusted. In case of excessive encrustation check the carbu Add some high speed gear grease in the gearbox After 50 hours of use Remove the filter as shown in the figure and clean it using a gentle jet of compressed air. For more thorough cleansing, you can wash it with soapy water. After 25 hours of use der to avoid overheating the motor, remove any dust and dirt from the slots on the cylinder cover and finds of the cylinder using a wooden scraper. Store the machine in a dry place. H1. After every use If you use the machine in an exceptionally dirty or dusty environment these operations should be carried out more often. H2. Replacement of nylon string (A) To replace the reel of string, press both the release pawls indicated by the arrows, remove the empty reel, unroll any string left and rewind the new string. Open the original package of string and insert the ends of the two strings in the eyelets on the reel, then wind the strings completely on the reel in the same direction and fasten the end of each string in the 2 opposite grooves. Replace the reel in its housing and thread the ends of the strings in their bushings. Pull each string so that about 15 cm comes out on each side. Reassemble the nylon string head as shown (fig. H5). If the reel becomes excessively worn, replace it with a whole new reel. H3. Replacement of nylon string (B) 1) L...

Descargar ahora

Introduzca dos números de la imagen: