Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Electrolux Tamaño del archivo: 1 mb Nombre del archivo: Idioma del manual:

Never sharpen a damaged blade: replace with a new one. Kickback can also occur when cutting with any type of blade in the hazardous zone (see I3). Do not let the blade cut in the risk sector to prevent kickback. C. Description of the safety devices on the machine Safety lever Never use the machine with its Safety lever pressed with adhesive tape, string or other. This device serves to prevent accidentally press- ing the throttle trigger (fig. A no. 3). In fact, the trigger (fig. A no. 3), can only be pressed if the safety lever is pressed at the same time (fig. A no. 17). By means of 2 separate springs, upon eleasing the grip, the throttle trigger (fig. A no. 3) and safety lever (fig. A no. 17) return automatically to their original positions. Antivibration device The machine is equipped with an antivibration device which serves to reduce the vibrations transmitted to the operator. Engine stop device the stop button Stop (fig. A no. 7) to O / STOP to stop the engine. To make sure this but- ton works properly, start the engine and check that it stops when the Stop button is turned to the Stop position. otection for transport The guard covers the sharp extremities of the blade when the machine is in the resting position for transport or storage. Safety guard This very important safety device (fig. A no.19) prevents any objects that come into contact with the cutting device, or the grass itself, from flying up and striking the operator. Safety pole guard This device, fastened to the machine, ensures a minimum distance between the operator and the cutting device during use, and prevents the machine from striking and injuring the operator if the blade hits a hard surface (fig. A no. 18). Muffler The muffler serves to reduce the noise level to a minimum and to route the exhaust fumes pro- duced by the combustion engine away from the operator. ness CAUTION! It is very important to familiarize yourself with the release mecha1 2 3 4 4 10 13 ENGLISH - 4 1 2 3 4 10 1 2 3 4 1 2 3 4 6 7 9 14 nism. In case of emergency you need to be able to release the machine quickly. The harness is equipped with a fasten-release mechanism. The harness enables the operator to support the machine during use (see “Safety precautions”, B7). D. Fuel Mixture Preparation of the mixture Filling the tank 7 14 15 Do not use any other type of fuel than the type recommended in this manual. This tions indicated in the table on the cover, fig. D. engines that use unleaded gasoline in the propor- = 90) and fully synthetic oil specific for two-speed unleaded gasoline (with a minimum octane rating and should therefore be fueled with a mixture of machine is equipped with a two-stroke engine Control the specifications of the oil shown on the package; the use of oil lacking the specifications expressly indicated in this manual could cause serious damage to the engine! To obtain the best mixture, pour the oil into an approved container first, followed by the gasoline, and shake the container well (every time you take fuel out of it). The characteristics of the mixture tend to deteriorate in time, so you should only prepare as much mixture as you are going to need (the use of deteriorated fuel can seriously damage the engine). 14 15 Clean the area around the fuel cap before removing it, to prevent any impurities from contaminating the fuel. Take the cap off the fuel container carefully. Unscrew the cap on the fuel tank and fill it with the necessary quality, using a funnel. During use, to prevent problems in starting the engine again, we strongly recommend that you avoid letting the fuel run out in the tank. Fuel storage 14 15 Store the fuel in a cool, well-ventilated place, in an approved fuel storage container. Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel. E. Assembly/disassembly E1. Delta grip 2 3 4 For your safety, fasten the delta handle in front of the label placed on the shaft at a distance of at least 11 cm from the rear grip. The handle should be fastened in a comfortable working position. If you are using sawtooth blades, the grip distance should be moved by at least 36 cm. The safety pole guard should be mounted using the accessories supplied and in the configuration shown in the figure,in contact with the delta handle. E2. Double handled grip (A) The grip (A) can be adjusted to suit the needs of the operator by moving it forward or backward. Loosen the knob, place the handle in the desired position then tighten the knob again. CAUTION! The handle assembly (A) can be E4. Fitting guard on line cutter head and grass cutting blade Adjust and secure double hand clamp by ...

Descargar ahora

Introduzca dos números de la imagen: