The driver installation will be finished in about one minute. Windows Setup Setup will load support for the following mass storage device(s): Intel(R) ICH8R/ICH9R SATA RAID Controller * To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S. * If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER. Figure 4 Only for GA-P35-DS3R. - 89 - Appendix English English Step 3: For GIGABYTE SATA2 SATA controller: When Setup correctly recognizes the GIGABYTE SATA2 SATA RAID/AHCI driver in the floppy disk, a controller menu similar to Figure 5 below will appear. Use the arrow keys to select one of the items displayed and press . If you set the Onboard SATA/IDE Ctrl Mode item in BIOS Setup to RAID mode, select GIGABYTE GBB363 RAID Controller (Windows 2K/XP/2003). (Select GIGABYTE GBB363 AHCI Controller (Windows 2K/XP/2003) for AHCI mode.) Windows Setup You have chosen to configure a SCSI Adapter for use with Windows, using a device support disk provided by an adapter manufacturer. Select the SCSI Adapter you want from the following list, or press ESC to return to the previous screen. GIGABYTE GBB363 RAID Controller (Windows 2K/XP/2003) GIGABYTE GBB363 AHCI Controller (Windows 2K/XP/2003) GIGABYTE GBB360 AHCI Controller (Windows 2K/XP/2003) GIGABYTE GBB362 RAID Controller (Windows 2K/XP/2003) ENTER=Select F3=Exit Figure 5 If a message appears saying one or some file(s) cannot be found, please check the floppy disk or copy the correct SATA RAID/AHCI driver again from the motherboard driver disk. When the screen as shown below appears, press to continue the driver installation from the floppy disk. The driver installation will be finished in about one minute. Windows Setup Setup will load support for the following mass storage device(s): GIGABYTE GBB363 RAID Controller (Windows 2K/XP/2003) * To specify additional SCSI adapters, CD-ROM drives, or special disk controllers for use with Windows, including those for which you have a device support disk from a mass storage device manufacturer, press S. * If you do not have any device support disks from a mass storage device manufacturer, or do not want to specify additional mass storage devices for use with Windows, press ENTER. I S=Specify Additional Device ENTER=Continue F3=Exit Figure 6 GA-P35-DS3R/DS3/S3 Motherboard - 90 - Step 4: After the SATA RAID/AHCI driver installation is completed, you can proceed with the Windows XP installation. WindowsXP Professional Setup Welcome to Setup. This port of the Setup program prepares Micros oft(R) Windows (R) XP to run on your computer. To set up Windows XP now, press ENTER. To repair a Windows XP installation using Recovery Console, press R. To quit Setup without installing Windows XP, press F3. | Enter= Continue R=Repair F3=Exit Figure 7 - 91 - Appendix English English B. Installing Windows Vista (The procedure below assumes that only one RAID array exists in your system.) Intel ICH9R SATA controllers: ® Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears, select Load Driver. (Figure 8). Wh*f* do you w*i« to ■'tsull Widows' TmjIJu» I«S||KI 1)9« ^ OMfc 0 Un*Aec«M Sp«c« KO (M «00« Bl^“o u« Figure 8 Step 2: Specify the location where the driver is saved, such as your floppy disk (Figure 9). S«l«ct tv 6m*i tc btiiWed. ■» N m tw ao (X ■ utMCC>:: 9 H.J. *..»1 9* I at 1 CM | I >»—« | ]_ e«<»" U*t Figure 9 ® Only for GA-P35-DS3R. GA-P35-DS3R/DS3/S3 Motherboard - 92 - Step 3: When a screen as shown in Figure 10 appears, select Intel(R) ICH8R/ICH9R SATA RAID Controller (Note) and press Next. o*-- — Select trw driver to be ¡nsufed. »w— 1 [ t*«*» 1 um 1 Figure 10 Step 4: After the driver is loaded, select the RAID/AHCI drive(s) where you want to install the operating system and then press Next to continue the OS installation (Figure 11). MM Where do you w*it to «$«11 Wodowi’ N.m, Td.i Sue Fnt$pM< T,p. . ^ oxtoun^MMSeMc »oca tea c* «»**** tflMdO».« 1 ““ft Figure 11 (Note) The item displayed in Figure 10 will be shown as Intel(R) ICH9 SATA AHCI Controller when the SATA controllers are set to AHCI mode. - 93 - Appendix English English GIGABYTE SATA2 controllers: Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears (RAID/AHCI hard drive(s) will not be detected at this stage), select Load Driver. (Figure 12). MW wv»r* do you w*nc to incuii window? 'u»» UulStf* I'K Sf«« Tft* On,« tptoon ^ Nc «Mmu...
