Votos - 4, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Also be sure items such as loading conveyors are not attached to or leaning on the mixer. Refer to scale manual for more specific information. 3. Mixer should be mounted on a structure of adequate strength to support a fully loaded mixer. Machine must be level and stable at the desired height. Weigh bar mounts should be fastened to this structure. 4. Manual door opener for the 3115 & 3120 can be mounted at either the front or the rear of the mixer. The following instructions will help to modify the door opener for operation from the opposite end: A. Remove latch and mounting bolt and install to opposite end of mixer in corresponding hole. B. Remove door wheel assembly. C. With door in fully closed position, cut door wheel shaft to proper length, drill mount hole, slide into position and replace bolt. 5. The 3125, 3130, 3136, 3142, 3150, 3160 and 3170 manual door opener is in a fixed position on the drive end of the mixer. 6. An optional remote electric door actuator is also available for the 3115 and 3120 models. An electric/hydraulic power pack is available for the 3125 through 3170 models. The power pack is standard on the 3195. NOTE: When wiring the electric/hydraulic power pack, make sure to wire it to a switched source and ensure it only runs when the door is activated. Electric Motor Recommendations Following is a listing of suggested motor and frame sizes. Ratings are based on “normal dairy feed rations”. Contact the factory if intending to mix heavier loads such as feedmill use, heavy/sticky beef rations or industrial use. A smaller motor may be adequate for easy-mixing materials and a larger motor may be required for difficult materials. Wiring and overload protection should be sized according to the motor size installed. The motor mount will fit the recommended motor size. Other motor sizes may require additional holes to be drilled in the mount or a different mount assembly. Dual motor mount, frame and shield are standard on 3125, 3130, 3136 & 3142 models. All models are designed to be used with a motor operating at 1725-1750 RPM. MODEL *HORSEPOWER OPTIONAL MOTOR BUSHING MOTOR FRAME SIZE STANDARD MOTOR BUSHING 3115 7.5 - 10 213T - 215T 1-3/8” 3120 10 215T - 254T 1-3/8” 3125 10 254T - 256T 1-5/8” 3130 10 - 15 254T - 256T 1-5/8” 3136 15 - 20 256T - 284T 1-5/8” 3142 15 - 25 284T - 286T 1-7/8” 3150 50 326T 2-1/8” 3160 60 364T 2-3/8” 3170 70 365T 2-3/8” 3195 100 N/A 2-7/8” A smaller motor may be adequate for easy-mixing materials and a larger motor may be required for difficult materials 1-1/8” 1-5/8” 1-3/8” 1-3/8” 1-7/8” 2-1/8” 2-1/8” 2-3/8” 2-3/8” © Copyright 2004 Kuhn Knight, Inc. Back to Table of Contents 3100ST 006046 010507 MIXER SETUP READ AND FOLLOW THESE INSTRUCTIONS WHEN SETTING UP THE MIXER. To avoid personal injury: The hopper floor may be slippery and the augers or reel can spin unexpectedly when stepped on. Use caution when stepping or standing inside the unit; put a protective cover over the auger knives. SAFETY SHIELDS Be sure all shields are in place and functioning properly. Replace all damaged or missing shields immediately; see Parts Manual for replacement shield part numbers. BE AWARE that your installation may require additional safety shields and/or warnings. Because each installation is different, Kuhn Knight Inc. cannot design standard shields for all conceivable situations without limiting the use of the mixer. The top of the mixer and the door opening are the two areas that should be given particular attention in regard to safety. The top of the mixer has a grid type safety shield to help prevent a person from falling into the mixer. However, because there are many different feeds and ways of loading them, the top openings must be large enough to avoid obstructing the loading operation. Likewise, the door opening area must be unobstructed to allow the discharge of feed. Kuhn Knight Inc. warns operators using decals on the mixer and specific instructions in this manual to stay clear of these areas during operation. If safety decals are blocked from view due to the installation, then additional decals should be ordered and placed so they are readable. If your particular installation is such that a person may inadvertently put an arm or leg in these areas during operation, then additional safety shielding must be installed to prevent such an occurrence. Drives, u-joints, sprockets and pulleys underneath the unit may become exposed if the equipment is mounted at an elevated height. Additional shielding of these areas may be necessary depending on exact installation. AUGER KNIVES The upper auger knives are installed to help handle long materials such as long stem hay. If you do not intend to handle this type of material, the knives can be removed. Commercial Reel models ordered with the Grain Series package do not include knives unless a Hay Maxx System was installed. REEL CROSS TUBES The cross tubes have two settings which can be utilized depending on the material being mixed. T...
Otros modelos de este manual:Mezcladoras - 3100 (1.05 mb)
Mezcladoras - 3100 (1.05 mb)