Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
ROUGHAGE MAXX SYSTEM A system of additional lower auger scallop knives that enhance hay processing performance of the reel mixer, with or without the optional Hay Maxx System. It is designed to allow the lower auger to do more cutting of long stem hay and roughages, even after hay has been introduced to the ration through the Hay Maxx System. © Copyright 2004 Kuhn Knight, Inc. Back to Table of Contents 3100ST 006046 010507 INSPECTIONS AND ADJUSTMENTS Always stop mixer and lock out the power before servicing, repairing or cleaning the machine. If work must be done inside the mixer, put a protective cover over the auger knives to avoid injury. The hopper floor and fighting may be slippery. Use caution when stepping on or standing inside the machine. Use safe shop procedures and exercise caution when working on the mixer! INSPECT AND ADJUST... ...Roller Chain Tighteners so they will apply sufficient spring tension to keep roller chains running smoothly. As a general rule the thickness of a nickel should fit between the spring coils. The chain will form grooves in the tightener blocks. These grooves help to keep the chains in proper alignment and the blocks need not be turned unless the roller portion of the chain has worn into the block. ...Roller Chains for wear, proper alignment and tension. Adjust or replace if necessary. Roller chain connector links, which pass over polyethylene tightener blocks, must be installed with legs of the cotter pins trailing to the direction of rotation. ...Safety Decals for legibility. If any safety decals are removed, obstructed, or otherwise not understandable, they should be replaced immediately. Keep all decals clean - see SAFETY DECALS in the SAFETY section for more information. ...Safety Shields to be sure all shields are in place and functioning properly. Replace all damaged or missing shields immediately - see Parts Manual for shield part numbers. ...Bolts and Set Screws after a few hours of use and each month thereafter. Tighten if necessary. ...Reel Cross Tubes so that they slide in freely when compressed against the spring; the spring pockets may need occasional cleaning. This sliding action helps prevent jamming and avoids overloading of the driveline. ...Reel Wiper Tubes for the condition of the plastic wiper strips, which help material clean out of the reel hopper. If the strips become bent backward, they can be unbolted and be reinstalled backward or replaced to improve clean out. ...Knives for damage or wear. Upper Auger Knives can be turned over for use of a new cutting edge and should be periodically sharpened or replaced if they no longer sufficiently break up material. Round Lower Auger Knives can be rotated several times before sharpening or replacement is required. Bolt-on Scallop Knives are to be replaced when they are worn. Small Knives on the flighting perimeter are to be welded in when replacement is necessary. ...Motor Fan Guard. The fan guard must be kept clean to allow sufficient air flow for proper motor cooling. ...Drive Belts for wear and hardness. Old belts will be brittle or hard and must be replaced. Pulley misalignment often causes belt wear and this alignment should be checked when replacing any worn belt. Inspect pulleys for wear or damage both on the grooves and on the shaft diameter. Clean and dry belts thoroughly before reassembly. Tighten belts to a tension that will allow the belt to deflect 1/2” when a 10lb. force is applied in the middle of the belt span. Belts should be kept clean, dry and oil free. IMPORTANT: WHEN WELDING ON THIS UNIT: DO NOT allow the current to flow through the bearings, roller chains, or scale weigh bars. Ground directly to the item being welded. ALWAYS disconnect weigh bar cords from scale indicator before welding. Back to Table of Contents Kuhn Knight, Inc. 1501 West 7th Ave., Brodhead, WI 53520 701 Cherry Ave., Greeley, CO 80632 26 3100ST 006046 010507 © Copyright 2004 Kuhn Knight, Inc. Back to Table of Contents INSPECTION AND ADJUSTMENTS IMPORTANT! Read before operating mixer. It is the responsibility of the owner to make sure the mixer is set up properly. The following recommendations should be helpful. ELECTRONIC SCALES Scale Indicator: Refer to the electronic scale operator’s manual for adjustment information. The operator’s manual for the Electronic Scales should be kept with this manual. Additional copies of scale manuals may be obtained through Kuhn Knight, Inc. Load cells and weigh bars should be kept clean, dry and lubricated to ensure dependability. NORMAL SCALE ACTIVITY Some warm up scale drift may occur after the scale is turned on but should zero balance within 10 to 15 minutes. Scale may zero shift over night due to temperature changes. 3150 TO 3195 AND 3136 BEFORE S/N B0001, 3142 BEFORE S/N B0001 Vertical check bolts must not be tight and should be free to rotate by hand. There should be 1/16” to 3/32” free play when properly adjusted on level ground. 3150 - 3195 AND 3136 BEFORE S/N B0001, 3142 ...
Otros modelos de este manual:Mezcladoras - 3100 (1.05 mb)
Mezcladoras - 3100 (1.05 mb)